answersLogoWhite

0


Best Answer

Dryer plug three to four

Open up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: You are trying to change a 3 prong cord to a 4 prong your new dryer has two green cables attached to the inside of the dryer?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

A loud pop when trying to jump start?

Cables backwards.


Sears Tractor runs only with jumper cables attached to a good battery After disconnecting the cables the tractor engins within seconds It's a 17 Hp Kohler engin on a Sears 42 mower tractor?

If the tractor had a battery in it when you were jumping it, there is a chance that the battery is bad. Try unhooking the tractors battery and trying again. Hook your jumper cables to the battery cables themselves without being attached to the battery. If it runs then just replace the battery. A battery with a short in it will keep the mower from charging and could cause it to die. If there was no battery in the tractor when you were jumping it, then the tractor is not charging and will have to be diagnosed as to what the problem is.


Why does your body temperature change when you are ill?

Your body is trying to make it hot enough on the inside to kill the invaders.


Trying to hook up sound to playstation 3 with component cables?

With component cables only the red and white are for sound and the other 3 are for video.


How do you adjust parking brake travel on a 2000 Dodge Grand Caravan the dealership is trying to sell a 350 dollar ratchet but the ratchet works fine suspect stretched cables can cables be adjusted?

Yes, cable can be adjusted . Somewhere in the main brake cable there is a square frame adjuster you change with 2 wrenches.


Can a governor on a International harvester engine stop the starter from turning over The governor makes a clicking sound when trying to start but the starter does nothing the solenoid has been change?

make sure battery cables are tight


Why would a car click when trying to jump start it?

The battery voltage is not high enough to start the car. The clicking is the solenoid trying to get enough power to activate the started motor. Try leaving the cables connected longer or try to get a better connection on the cables.


Why do jumper cables melt when trying to jump start a car even when they are hooked up correctly?

There its too much current running through them. If they are hooked up properly then you either have a short some where (positive wire that is touching ground) or the jumper cables can't handle the current demanded by the vehicle you are trying to start. If this is the problem, you need jumper cables that are a thicker gage wire.


What types of battery cables should one use when trying to jump start a dead battery?

Jumper Cables. If your battery has died, you may be able to use jumper cables to jump start it from some good Samaritan_Ü_s vehicle. If you can safely use jumper cables on your vehicle, make sure that the battery on the good Samaritan_Ü_s vehicle has at least as much voltage as your own.


How do you take off cabels on a VW Beetle?

Which cables are you trying to remove? They either pull off, or the ends are bolted/screwed down.


How do you change a bulb in my Toyota Echo?

Which bulb are you trying to change?


Can you plug in an x box 360 to a smart board just trying to find out so name can show his class a utopia on Mine craft?

Yes, just connect the AV cables (they are red, yellow and white) to the projector and change the input settings to show it on the board.