0
What else can I help you with?
How big of a generator do you need to drive a 200 amp welder?
When you refer to a 200 amp welder you are talking about the output side of the welder. What you have to do is find out what the input voltage and current of the welder is to calculate the size of a generator needed to operate the welder.
Can you run a 220 volt welder on a 20 amp breaker?
Yes, you can run a 220-volt welder on a 20-amp breaker, but it depends on the welder's amperage requirements. If the welder draws more than 20 amps, it could trip the breaker or damage the welder. It's essential to check the welder's specifications and ensure that the circuit can handle the load safely. If the welder requires higher amperage, a breaker with a higher rating may be necessary.
How many amp cutoff switch for a 250 amp welder?
For a 250 amp welder, a common practice is to use a cutoff switch rated at least 25% higher than the welder's output. This means a cutoff switch rated for around 300 amps would be appropriate to ensure safe operation and handle potential inrush currents. Always consult the welder's manufacturer specifications and local electrical codes for specific requirements.
What do the numbers on fuses signify?
That is the amp load the fuse can handle before it fails.
Will a 5000 watt amp wiring kit work well on a 1600 watt amp?
Yes I do not see why not as long as the in line fuse does not exceed the power the amp is pulling. You want the fuse to blow instead of the amp so you need a fuse that can only handle 1600 watts or the equivalent to....
Can a 3.15 amp fuse be used to replace a 4 amp fuse?
No, a 3.15 amp fuse should not be used to replace a 4 amp fuse. The 4 amp fuse is designed to handle higher current loads, while the 3.15 amp fuse may blow prematurely under those conditions, potentially leading to circuit failure or equipment damage. Always replace fuses with one of the same rating to ensure proper protection and functionality.
How do you write a sentence using fuse?
The welder will fuse the edges of the metal door so that it remains permanently shut.
Can you plug a 120v 20 amp wielder into a 240v 40 amp outlet?
No, it is not safe to plug a 120v 20 amp welder into a 240v 40 amp outlet. The voltage difference is too high and could damage the welder. It is important to match the voltage and amperage of the welder with the corresponding outlet.
What are the correct fuses to use in the fuse box of a peugeot 205 gti 1.9 1989?
fuse number 1 is 10 amp fuse 2 is 25 amp fuse 3is 25 amp fuse 4 is a spare fuse 5 is 10 amp fuse 6 is a spare fuse 7 is 20 amp fuse 8 is 25 amp fuse 9 is 20 amp fuse 10 is 5 amp fuse 11 is 5 amp fuse 12 is a spare fuse 13 is 5 amp fuse 14 is 15 amp
What is the difference in a 5 amp fuse and 6 amp fuse?
The main difference between a 5 amp fuse and a 6 amp fuse lies in their respective current-carrying capacities. A 5 amp fuse is designed to safely carry up to 5 amperes of current before breaking the circuit to protect the electrical components from damage due to overload. On the other hand, a 6 amp fuse can handle up to 6 amperes of current before breaking the circuit. Therefore, the 6 amp fuse has a slightly higher current rating and can tolerate a slightly higher load compared to the 5 amp fuse.
Can you use a 15 amp fuse instead of a 10 amp fuse for your car gauges?
It is NEVER a good idea to use a higher value fuse. The reason for the 10 Amp fuse is that it blows at 10 amps which the wire and device being protected is designed to handle. If you substitute 15 amps and that amount of current flows in your device, it may destroy the device and other things in the path of the current.
Would a 135 amp welder work on a 2.4hp generator?
no
