Yes provided the voltage is compatible.
Yes, a space heater can be plugged into any outlet. Depending on what else is drawing current on the circuit will govern whether the circuit will trip or not. If the heater is plugged in and the circuit does not trip it can be left plugged as long as it is needed. If the heater trips after a few seconds, then try another outlet.
One reason could be that the heater was wired into the lighting circuit so that when the heater is turned on its high current draw causes the circuit breaker to "trip" to shut off the current.A lighting circuit is intended to be used only for lights.Further answer for USA, Canada and countries running a 60 Hz supply service.A small electric heater - under 2 kilowatts in power - should only ever be connected into a branch circuit feeding power outlets, providing you have checked that the circuit's existing circuit breaker and cable size are of the appropriate ampacity to be able to take the extra current draw safely.If it is over 2 kilowatts in power it should be connected into its own dedicated circuit using:correct type of circuit breaker unit of the appropriate ampacitycorrectly sized cable and eithercorrect type and size fixed outlet (non-pluggable) orcorrect type and size socket outlet taking an appropriate plug.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Current in amps = watts/ voltage in volts. If you have a 240 volt supply, it will draw 4800/240 = 20 amps, so no. This is a very powerful water heater, and would normally be wired into a dedicated circuit, presumably with a 30 amp breaker.
does the bypass valve on elution heater be open or closed
The clicking noise you are hearing could be the heater is overloading the breaker and it is on the verge of tripping This could be caused by the heater being to large for the circuit. Check the amperage rating on the heater and the rating on the breaker It also cold be the circuit breaker is going bad and needs to be replaced by a qualified electrician These are 2 possible answers you also could have a bad (loose) electrical connection some where in the circuit
To get to the bulb for lighting the heater controls, the front panel will have to be removed. Depending on the type of vehicle, the knobs might have to be popped off first. It is also possible on some vehicles to get to the lighting for the heater controls from under the dash.
Yes, a space heater can be plugged into any outlet. Depending on what else is drawing current on the circuit will govern whether the circuit will trip or not. If the heater is plugged in and the circuit does not trip it can be left plugged as long as it is needed. If the heater trips after a few seconds, then try another outlet.
Connect incoming power to the line side of GFCI outlet and plug Jacuzzi into the outlet. Must be on a dedicated circuit. If it has a pump and heater then each one must be on dedicated GFCI protected circuit.
Environment Circuit
heater sensor circuit Chevy astro 2000
The circuit is open. Wires could be disconnected/damaged or the heater element is burned out.
One reason could be that the heater was wired into the lighting circuit so that when the heater is turned on its high current draw causes the circuit breaker to "trip" to shut off the current.A lighting circuit is intended to be used only for lights.Further answer for USA, Canada and countries running a 60 Hz supply service.A small electric heater - under 2 kilowatts in power - should only ever be connected into a branch circuit feeding power outlets, providing you have checked that the circuit's existing circuit breaker and cable size are of the appropriate ampacity to be able to take the extra current draw safely.If it is over 2 kilowatts in power it should be connected into its own dedicated circuit using:correct type of circuit breaker unit of the appropriate ampacitycorrectly sized cable and eithercorrect type and size fixed outlet (non-pluggable) orcorrect type and size socket outlet taking an appropriate plug.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
A standard domestic water heater in a house, apartment, etc will need 220 Volts AC. They have two heating elements upper and lower and each is 110 VAC hence the 220 Volt supply. Make sure it has a dedicated circuit and a disconnect on the wall above and beside water heater.
That circuit is overloaded. Call an electrician to fix it for you.
The dash must be completely removed in order to gain access to the heater box. Then the heater hoses are disconnected and the heater box is removed and opened up. That gains access to the heater core for relacement.
The dash must be completely removed in order to gain access to the heater box. Then the heater hoses are disconnected and the heater box is removed and opened up. That gains access to the heater core for relacement.
The dash must be completely removed in order to gain access to the heater box. Then the heater hoses are disconnected and the heater box is removed and opened up. That gains access to the heater core for relacement.