Most definitely. GFCI receptacles have a test buton, and should be tested regularly. you can also buy inexpensive plug-in testers at most home centers and electric supply houses.
Not if the GFCI breaker is supplying the circuit you are wanting to put the GFCI receptacle into.
1. Check with local regulation , authorities. Go by the local law or regulation. 2. If the application is in wet area, risk of ground fault is more, hence go for GFCI.
A GFCI outlet has a TEST and RESET switch. Press reset and see if it fixes problem. If reset won't stay in that means that a ground fault condition is present and may be on another outlet that is fed from the tripped GFCI. If this isn't the problem check the main breaker feeding the GFCI and ensure it isn't tripped. If none of this works the GFCI itself may be bad. If you have a Volt Meter you can remove the outlet from the wall receptacle and make sure there is voltage present. You can also see if there is a branch circuit connected. To troubleshoot you can disconnect the branch circuit and then try reset. If you have voltage on input and GFCI won't reset with branch circuits removed, replace the GFCI.
Your question is a bit vague, but let's try a two part answer. If you have a GFCI breaker in an electric panel you should only have one connection at the breaker, but the breaker will protect all devices on the circuit. If you are talking about a GFCI outlet, they are equipped to extend the GFCI protection to other non-GFCI outlets by using the proper "output" connection on the GFCI.
Deoends on code you are governed by. In USA, a GFCI outlet or a circuit controlled by a GFCI circuit breaker would be required.
my gfci trips when my christmas lights r on and it rains is the gfci bad or is this normal of a perfectly working gfci
If the test switch is faulty then there is no convenient way to determine if the GFCI is functioning, and technically, if the test switch is faulty, then as it is a part of the GFCI, the GFCI is faulty and should be replaced.
Not if the GFCI breaker is supplying the circuit you are wanting to put the GFCI receptacle into.
GFCI protection is required for most outdoor receptacles, bathroom , garage wall outlets, kitchen, and all receptacles in crawl space.
This indicates either you have an active ground fault or the GFCI is bad. To check this out turn off power at breaker and remove GFCI outlet from wall box. Determine if it is powering other non-GFCI outlets. (It will have both input and output wires. If there are output wires remove them and check the outlet again with power and see if it resets. If it does you have a ground fault down the line somewhere. If it still doesn't work you likely have a bad GFCI.
There is three possible reasons for this. First, check to make sure that the breaker also did not trip, a GFCI outlet will not reset if not powered. Second, if the load that caused the GFCI to trip is still plugged in it will not allow the GFCI to reset. So, before trying to reset the GFCI unplug everything that it protects. Third, you might just have a bad GFCI, attempt the above suggestions first and if it still will not reset you will need to replace the GFCI. If after all this the you are still having problems then something more serious is wrong and you need an on site electrician to diagnose the problem.
Yes you can. Lots of blow dryers have GFCI protection built in.
In a word NO, that will not cause either GFCI to trip. The correct term is GFCI (Ground Fault Circuit Interrupter)
no, although it is not a bad idea, if the d-washer is close to the sink. safety first, not last
1. Check with local regulation , authorities. Go by the local law or regulation. 2. If the application is in wet area, risk of ground fault is more, hence go for GFCI.
A GFCI outlet has a TEST and RESET switch. Press reset and see if it fixes problem. If reset won't stay in that means that a ground fault condition is present and may be on another outlet that is fed from the tripped GFCI. If this isn't the problem check the main breaker feeding the GFCI and ensure it isn't tripped. If none of this works the GFCI itself may be bad. If you have a Volt Meter you can remove the outlet from the wall receptacle and make sure there is voltage present. You can also see if there is a branch circuit connected. To troubleshoot you can disconnect the branch circuit and then try reset. If you have voltage on input and GFCI won't reset with branch circuits removed, replace the GFCI.
GFCI Breakers are quite a bit more expensive than a GFCI outlet. More often than not a typical residence will need only a handful of GFCI outlets that combined together will be cheaper than a GFCI breaker. If you need to protect a series of outlets with GFCI protection you can simply connect the rest of the outlets on that same circuit downstream from the first outlet on the line and make that the GFCI. All you have to do is connect all the other outlets to the LOAD side of the GFCI outlet. If a GFCI fault occurs in any of the outlets down stream they will trip that very first GFCI plug you placed and keep you safe.