0
Can an ohmmeter be used to read a resistance while a source is connected?
Wiki User
∙ 15y ago
Yes. It NEEDS a source to be connected.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Should the ohmmeter be connected to the circuit while the power is being applied or only when the circuit is turned off?
Turn off the supply before using the ohmmeter,it will damaged your ohmmeter when supply is present.
What is the difference between a series ohmmeter and a shunt ohmmeter?
Basically, your series and shunt ohmmeters differ in circuit configuration. Your series ohmmeter is configured in a way that your "meter" (which has internal resistance) is connected in series to your "measured resistor" and we all know that those TWO resistances will ADD up causing some sort of inaccuracy. While on the other hand, your shunt ohmmeter is configured in a way wherein your "meter" is connected in PARALLEL to your "measured resistor" that will ease-up the inaccuracy but will only measure resistances ranging from 200 Ohms to 400 Ohms (typically and depending on your configuration).
Why multimeter cannot used for measurement of insulation resistance?
Because ordinary ohmmeters are calibrated to measure a range of resistance values that are significantly lower than the resistance of insulation. It should also be realised that we usually test insulation resistance while subjecting the insulation to a high electric field, which a normal ohmmeter is incapable of producing.
What is input impedance of a circuit?
Impedance is the total opposition to current flow. It includes both resistance AND reactance (capacitive and inductive). Impedance varies with frequency, while plain resistance does not. Scroll down to related links and look at: "Different names for the two impedances Z1 and Z2" "Calculation the damping of impedance bridging or power matching an interface connecting Zout and Zin" "Impedance bridging or voltage bridging of two audio units".
What is the diffrece between disconnected and connected environment?
Connected environment is one in which a user is required to be constantlyconnected to the Data Source while performing any operation in-order to keep the data up-to-date, whereas in Disconnected environment no constant connection to the Data Source is required.Moreover in connected environment the data concurrency effects can beeasily resolved but Connected environment causes network traffic. But in Disconnected environment since the user is not directly connected to the data source, the user can connect to the data source as and when required and hence it allows for Multiple applications to simultaneously interact with the Data Source. It also improves the scalability and performance of the applications.Few more differences can be contributed as the Connected Environment uses Datareader while the Disconnected one uses Dataset. This results in the fact that Connected Environment is Slower in speed in comparison to Disconnected environment for DML Operations. But as far the Connected Environment is concerned we get updated data and less chances of Dirty read, whereas Disconnected environment suffers from the major problem of Dirty read.Thanks & Regards,Shoaib R Khan - SRK
Should the ohmmeter be connected to the circuit while the power is being applied or only when the circuit is turned off?
Turn off the supply before using the ohmmeter,it will damaged your ohmmeter when supply is present.
What is the difference between a series ohmmeter and a shunt ohmmeter?
Basically, your series and shunt ohmmeters differ in circuit configuration. Your series ohmmeter is configured in a way that your "meter" (which has internal resistance) is connected in series to your "measured resistor" and we all know that those TWO resistances will ADD up causing some sort of inaccuracy. While on the other hand, your shunt ohmmeter is configured in a way wherein your "meter" is connected in PARALLEL to your "measured resistor" that will ease-up the inaccuracy but will only measure resistances ranging from 200 Ohms to 400 Ohms (typically and depending on your configuration).
What precuation must be taken when using an ohmmeter?
Be certain the circuit is de-energized and discharged before connecting an ohmmeter.Do not apply power to a circuit while measuring resistance.When you are finished using an ohmmeter, switch it to the OFF position if one is provided and remove the leads from the meter.Always adjust the ohmmeter for 0 (or ∞ in shunt ohmmeter) after you change ranges before making the resistance measurement.
Why must power be turned off when measuring the resistance of a circuit?
If an external Voltage is applied to a multimeter while the multimeter`s function switch is in the Ohm meter position then the Ohmmeter is apt to be destroyed or disabled. Therefore the simplest answer is that the power must be turned off in order to avoid damage to the Ohm meter and possibly to yourself caused by Voltages present in the circuit while the power is own. Another reason of course is because a valid Ohm reading can not be obtained while Voltages are present across the resistance that is being measured because the Ohmmeter itself applies a Voltage across the resistance and then a sampling of the current through the unknown resistance is used by the Ohmmeter`s circuitry to cause a calibrated deflection of the Ohmmeter and thus display on the meter`s dial the Ohmic value of the unknown resistance. For the same reasons as above it is also a good practice to discharge all the capacitors in the circuit after the power is turned off and before any in circuit resistance measurements are made.
Why one of the leads of resistor connected in electronic circuit is opened while measuring its resistance?
You open one of the leads of resistor connected in electronic circuit while measuring its resistance in order to not introduce error cause by other components in the circuit.
Why multimeter cannot used for measurement of insulation resistance?
Because ordinary ohmmeters are calibrated to measure a range of resistance values that are significantly lower than the resistance of insulation. It should also be realised that we usually test insulation resistance while subjecting the insulation to a high electric field, which a normal ohmmeter is incapable of producing.
How do you take care of an ohmmeter?
Never connect the ohmmeter's leads across a voltage.On an analog meter, adjust the zero before use.Turn your ohmmeter off when not in use, to protect against voltage drain.When your ohmmeter's battery is low, or your meter won't be used for a while, remove the battery to prevent damage to the meter from battery leakage.
What is principle of thermistor?
The thermistors are resistors whose resistance changes with the temperature. While for most of the metals the resistance increases with temperature, the thermistors respond negatively to the temperature and their resistance decreases with the increase in temperature. Since the resistance of thermistors is dependent on the temperature, they can be connected in the electrical circuit to measure the temperature of the body.
What dose in parallel mean?
parallel means they will never cross each other. take a example when a resistance connected in parallel then a current flowing through it(both resistance) is not same depended on the value of each resistance. while in the series circuit current values is same for both resistance. parallel lines are drawn below:- series lines:- -------
Explian the working of a common-source amplifier and a common drain amplifier?
Configuration Voltage Gain Current Gain Input Resistance Output Resistance Common- Source AV >1 - ∞ Moderate to high Source-Follower AV ≈ 1 - ∞ Low Common- Gate AV > 1 Ai ≈ 1 Low Moderate to high Both the common-gate and common source has voltage gain of greater that 1 compared with the voltage gain of source- follower which is less than or approximately equal to 1 . The input resistance of both common-source and source follower is high typically ranges from kilo ohms and above while common-gate has a low input impedance ranges from hundred ohms or below. The output resistance of both common-gate and common-source are dominated by RD while source follower has low output impedance and is not dominated by RD
Why human cells not getting resistance towards tobacco?
the ants getting resistance to DDT while the humans not getting resistance to tobacco? the ants getting resistance to DDT while the humans not getting resistance to tobacco- why
What is input impedance of a circuit?
Impedance is the total opposition to current flow. It includes both resistance AND reactance (capacitive and inductive). Impedance varies with frequency, while plain resistance does not. Scroll down to related links and look at: "Different names for the two impedances Z1 and Z2" "Calculation the damping of impedance bridging or power matching an interface connecting Zout and Zin" "Impedance bridging or voltage bridging of two audio units".
