No, silver was never used in BX cable.
It used to be, but now the ground wire (which replaced the aluminum strip) in the BX cable is used. The ground wire is now used to complete the grounding of connected devices rather that the sheath of the BX.
A BX connector is a special type of box connector used for securing a BX cable to a junction box. BX is a type of armoured cable that is used for specific locations where ordinary Romex cable could become damaged. Before the connector is installed onto the BX cable there is a small PVC collar to be installed. In the trade it is called an anti short. It slides between the outer sheath of the BX and the conductors inside the sheath. It adds protection for the inner conductors from rubbing against the outer sheath if any vibration is involved in the installation. There is usually a small hole in the BX connector and the red anti short can be seen through this hole. This makes it easy for the electrical inspector to see if the anti short bushing has been installed during an inspection, and they do check.
Yes it is but make sure you do not confuse it with "outdoors".
No, proform doesn't supply treadmills that are used outdoors. I don't know of any company that supplies treadmills that are used outdoors. Most treadmills are used indoors.
Bronx
.code main proc mov ax,@data mov ds,ax lea dx,msg ;printing msg mov ah,09h int 21h mov ax,x ;ax=x mov bx,y ;bx=y cmp ax,0 ;jump to l3 if ax is negtive jb l3 cmp bx,0 ;jump to l6 if bx is negative jb l6 cmp ax,bx ;if ax<bx,then jump to l1 jl l1 sub ax,bx ;else normal sub mov diff,ax ;diff=result is stored jmp l2 l1: ;iff (+)ax<(+)bx neg bx ;bx=-bx clc add ax,bx neg ax ;-ans=ans mov diff,ax mov dx,2dh ;print '-' mov ah,02h int 21h jmp l2 l3: ;iff (-)ax neg ax ;-ax=ax cmp bx,0 ;jump to l4 if bx is negative jb l4 clc add ax,bx ;ax=(+)ax+(+)bx mov ax,diff mov dx,2dh ;print '-' mov ah,02h int 21h jmp l2 l4: ;if (-)ax & (-)bx neg bx ;-bx=bx cmp ax,bx ;if ax>bx then jump to l5 jg l5 sub ax,bx ;else ax-bx mov diff,ax mov dx,2dh ;print '-' mov ah,02h int 21h jmp l3 l5: ;if(-)ax>(-)bx xchg ax,bx ;exchange ax and bx sub ax,bx ;ax-bx mov diff,ax ;ans is positive jmp l2 l6: ;iff (-)bx neg bx ;-bx=bx add ax,bx ;ax-(-)bx mov diff,ax ;ans will be positive mov ah,4ch int 21h main endp
I have a code for 16 bit subtraction.. just replace ax by al,bx by bl etc... .code main proc mov ax,@data mov ds,ax lea dx,msg ;printing msg mov ah,09h int 21h mov ax,x ;ax=x(any number) mov bx,y ;bx=y( " ") cmp ax,0 ;jump to l3 if ax is negtive jb l3 cmp bx,0 ;jump to l6 if bx is negative jb l6 cmp ax,bx ;if ax<bx,then jump to l1 jl l1 sub ax,bx ;else normal sub mov diff,ax ;diff=result is stored jmp l2 l1: ;iff (+)ax<(+)bx neg bx ;bx=-bx clc add ax,bx neg ax ;-ans=ans mov diff,ax mov dx,2dh ;print '-' mov ah,02h int 21h jmp l2 l3: ;iff (-)ax neg ax ;-ax=ax cmp bx,0 ;jump to l4 if bx is negative jb l4 clc add ax,bx ;ax=(+)ax+(+)bx mov ax,diff mov dx,2dh ;print '-' mov ah,02h int 21h jmp l2 l4: ;if (-)ax & (-)bx neg bx ;-bx=bx cmp ax,bx ;if ax>bx then jump to l5 jg l5 sub ax,bx ;else ax-bx mov diff,ax mov dx,2dh ;print '-' mov ah,02h int 21h jmp l3 l5: ;if(-)ax>(-)bx xchg ax,bx ;exchange ax and bx sub ax,bx ;ax-bx mov diff,ax ;ans is positive jmp l2 l6: ;iff (-)bx neg bx ;-bx=bx add ax,bx ;ax-(-)bx mov diff,ax ;ans will be positive mov ah,4ch int 21h main endp
Citroën BX was created in 1982.
BX Warrior was created in 2006.
Toyota BX was created in 1951.
Yes it can