0
I'm sure you could rig something up with some serious work, but I'd suggest sticking with electrical. The electrical switch controls a motor that is attached directly to your transfer case. There's no linkage there to work with. The motor turns a shaft to shift between 2wd, 4wd hi, and 4wd low.
What else can I help you with?
Why is my 1995 Chevy blazer 4x4 not working all the time?
You may need to replace the 4x4 engager switch or replace the fuse in your fuse box.
How do you adjust the linkage on a 92 Nissan 4x4 pick up?
What linkage?
How does the linkage switch from a quadrajet carb to an Edelbrock 600 cfm with a manual choke carb you are working on a 1985 Chevy 4x4 with a sb350?
Ubbv
How do you replace the hazard button on a 1996 blazer 4x4?
The hazard button alone can't be replaced. You will need to replace the complete signal switch which is called a multifunction switch.
Can you replace the 29 engine in a 1990 Ranger XLD 4x4 electric shift with a 40 engine?
== ==
How do you replace a dimmer switch for a 1987 Chevy truck 4x4?
how do you replace3 dimmer switch 1987 chevy silverado 4 x 4
What causes the pushbutton style 4x4 to try to switch into fwd lo when normal driving?
Howdy, Pushbutton 4x4 use a electric motor to move the shifter fork in the transfer case to 4x4 and then into 4wd Lo range. This unit has a electric motor, a small gear box and a contact switch inside this little unit that is mounted to the transfer case. The contact switch is very light duty, and will either wear out or corrode from road salts, water, etc. I have had many apart and the only way to fix this problem is to change the complete unit (Around $175.00) as they are not repairable. I have had a few apart to see exactly the workings. What is happening is when your switch in in one position on the dash, the switch will make a contact in the contact switch on the motor telling the computer to turn on a light, which in turn makes to electric motor engage the transfer case into another position that you didn't call for, like 4x4 or 4x4 LO. Replace this motor assy or it will tear out your transfer case. E-mail with more questions. cowboysairranch@wildblue.net
How do you bypass neutral safety switch on 1995 Chevrolet 4x4?
You can't. There are 2 many other electronic devices that run through the switch. You must replace the switch.
1991 explorer and the 4x4 led will not light upor switch to 4x4 high or low even after changing the switch and 4x4 motor please help?
My Explorer did that and I had to take the dash panel out where you will find a black or green box right beside where the radio goes, you will have to replace it.
Where is the backup light switch and how do you access it on a 1995 Suzuki Sidekick 4X4 with automatic transmission?
On a 1995 Suzuki Sidekick 4X4 with an automatic transmission, the backup light switch is typically located on the transmission itself. To access it, you'll need to raise the vehicle safely and remove any undercarriage covers if present. The switch is usually mounted on the transmission housing near the gear selector linkage; you may need to disconnect the electrical connector and unscrew the switch to replace it if necessary. Always consult the vehicle's service manual for specific details and procedures.
Where is the 4x4 switch in a 95 jeep grand Cherokee?
there is a 4x4 switch on the transfer case. i found it when my vehicle control center said to "service 4x4 switch"
How do you change the neutral safety switch on a 1999 Jeep Grand Cherokee Laredo 4x4?
the neutral safty switch is located in the trans range switch if you have an aw4 auto trans replace or clean and reinstall the switch
