Yes, as long as it is just incandescent bulb lighting connected to the track. If there is a transformer between the voltage source from the track and the light bulb (e.g. low voltage quartz bulbs) then these fixtures can not be dimmed.
No. Fluorescent lights operate through an electrical ballast which regulates the voltage and amperage, and you will ruin the ballast if the correct VA is not provided. The reason that fluorescent lights are used is because of their low wattage requirements.
No, ordinary fluorescent lamps won't work with a dimmer. You have to install special bulbs and fixtures that are designed to be dimmed.
. A halogen light bulb is very similar to an incandescent bulb. The Halogen bulb usually last a little longer and burn a little brighter. The Halogen bulb can be use with a dimmer.
No. To dimmer Fluorescente lamps, needs a special reactor.
Yes, but the ballast has to be of a special manufacture to make this happen.
yes!
Halogen is a type of incandescent fixture so yes.
If you use a non-dimmable Compact Fluorescent Lamp (CFL) in a circuit controlled by a dimmer switch no damage will be done but the CFL will stay bright when the dimmer is turned down whilst any other normal incandescent lamps wired into the same circuit will go dim in the normal way.Dimmable Compact Fluorescent Lamps are now available, for example in the Megaman range of CFLs. For more information see the Related Link shown below.Incandescent dimming uses any incandescent lamps and an incandescent dimmer.To dim fluorescent lamps usually requires use of fluorescent dimmers AND fluorescent dimmable ballasts. If these two components do not match, dimming will not work.The fluorescent lamps themselves are the same whether you put them in a standard (nondimming) ballast or a dimmable ballast.If your dimmers are not dimming the CFLs they are either not fluorescent dimmers or, more likely, your ballast in the light fixture is not a dimmable ballast.
Although a dimmer can be designed for 12 v halogen lamps it is more common for dimmers to work on higher voltages. Dimmers have to work into a resistive load so it is not usually possible to place the dimmer on the high-voltage side of the 12 v transformer that comes with the lights.
I'm going to assume that the switch that's getting warm is the dimmer. Even when a dimmer is working correctly it gets warm and that's just the electronic parts of it. The face of a dimmer is actually a heat sink to help remove excess heat. If you swap out the dimmer you will likely find your problem is resolved. Remember to de-energize the circuit by turning off the breaker before working on it. If in any doubt, consult a qualified electrician. Andy Be aware that a dimmer for lights does NOT work for fans (though it may sometimes appear to work, you can end up with noise, problems such as the light attached to the fan not working, the dimmer getting overheated, etc). So even though it might seem to work at first, you'll have problems, and it's against code to put the wrong kind of dimmer there. You can purchase a dimmer which is rated for ceiling fans at Home Depot or Lowes, but they are more expensive than light switch dimmers. Of course, if there is a single on/off switch at the wall which controls the fan and its light, then you might be better off buying a remote control unit to install in the fan - it will allow you to dim the fan and light separately (and safely). Or purchase a new fan with a remote... ceiling fans are cheap enough now that if yours is old enough, it might be a nice time for an update.
Yes, you can put a fluorescent light bulb in your floor lamp. You need to see what size bulb the lamp takes, but most sizes can be purchased as florescent bulbs.
I have but if dimmer is on low the light fixture sometimes "hums", can be anoying It also shortens the bulb life, significantly in some cases. But their are also CFL bulbs built to be used with a dimmer switch that avoid these problems.Another AnswerYou should only use CFLs specifically-designed to be used with dimmers in circuits controlled by dimmer switches. There is a proven danger of fire hazard when ordinary CFLs are controlled by dimmer switches and, so, this should NEVER be done.
Yes. There are various types of dimmers. Look for the halogen dimmer in your favorite search engine.
They as designed to "dim" when headlights are on to reduce "glare" try adjusting dash dimmer switch
need to know the capacity of the dimmer and the size of the lights
you can not put a normal dimmer on a florescent light. You need to install a dimmer made for flourecent lights and they are expensive about 50 dollar around here. If you want to dim it put a normal incandescent bulb in the fixture.
Halogen is a type of incandescent fixture so yes.
try your dimmer switch just put one in my 97 that was my problem
If you use a non-dimmable Compact Fluorescent Lamp (CFL) in a circuit controlled by a dimmer switch no damage will be done but the CFL will stay bright when the dimmer is turned down whilst any other normal incandescent lamps wired into the same circuit will go dim in the normal way.Dimmable Compact Fluorescent Lamps are now available, for example in the Megaman range of CFLs. For more information see the Related Link shown below.Incandescent dimming uses any incandescent lamps and an incandescent dimmer.To dim fluorescent lamps usually requires use of fluorescent dimmers AND fluorescent dimmable ballasts. If these two components do not match, dimming will not work.The fluorescent lamps themselves are the same whether you put them in a standard (nondimming) ballast or a dimmable ballast.If your dimmers are not dimming the CFLs they are either not fluorescent dimmers or, more likely, your ballast in the light fixture is not a dimmable ballast.
on some i think you can there will be 2 switches on a panel bord and 1 will be dimmer then the other or on other trees there are different patterns some dim some very bright
The regular switch just connects in the circuit the same way as the dimmer switch came out. If the dimmer switch had its own wires the only difference will be is you will have to supply your own wires from the new switch to the existing connection. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS. If you do this work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized.
I'm not sure what you mean by turning a dimmer switch "up".-- When the dimming action of the device is turned 'up', the bulbbecomes more dim, that is, less bright.-- The dimmer may have an arrow printed on its control, labeled 'brighter'.In that case, when you turn the control in the direction of the arrow,the light becomes brighter, i.e. less dim.
Although a dimmer can be designed for 12 v halogen lamps it is more common for dimmers to work on higher voltages. Dimmers have to work into a resistive load so it is not usually possible to place the dimmer on the high-voltage side of the 12 v transformer that comes with the lights.