answersLogoWhite

0

you can not put a normal dimmer on a florescent light. You need to install a dimmer made for flourecent lights and they are expensive about 50 dollar around here. If you want to dim it put a normal incandescent bulb in the fixture.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Art & Architecture

Where is the headlight dimmer switch located on a 2004 Chevy Blazer S-10 and how do you replace it?

dimmer switch is on the turn signal lever, to replace you need to remove steering wheel


When you click for bright lights the headlights go out What do you do?

This is usually an indication that the dimmer switch is in need of replacement.


Is there a switch on the steering column that goes to the windshield wiper motor on a 1991 jeep wrangler yj?

Yes there is. On the 1987 thru 1995 models the switch is located on the left side of the steering column.Its multi function controling the wiper/washer, turn signal and dimmer switch.


How would you repair the headlights on a 1995 GMC Safari van that worked until the steering column was replaced?

They might have forgoten to plug the dimmer switch back in. The dimmer is attached to the column. Find someone to look under the dash, or take it back to whoever replaced the column. It would be their responsibility to make sure everything is right.


Why do low beams work but not high beams 1991 ford escort?

This is normally caused by the dimmer switch going bad. In fact, I know of no other possibility, other than the low beam of the driver's side lowbeam input wire being pinched or cut in two. The latter is a very slight possibility, but is still possible. It is very much more likely to be the dimmer switch being bad.One lady brought me her Merc Sable, with that problem...both her dim lights were blown,and would only work on hi beam....sigh...some people....

Related Questions

How can I troubleshoot and fix a LED light flickering issue when connected to a dimmer switch?

To troubleshoot and fix a LED light flickering issue when connected to a dimmer switch, you can try the following steps: Check if the dimmer switch is compatible with LED lights. Some dimmer switches are not designed to work with LED bulbs and can cause flickering. Make sure the LED bulb is compatible with the dimmer switch. Not all LED bulbs are dimmable, so using a non-dimmable bulb with a dimmer switch can cause flickering. Replace the dimmer switch with one that is specifically designed for use with LED lights. This can help eliminate flickering issues. If the flickering persists, consider installing a load resistor or a bypass device to stabilize the current flow and prevent flickering. By following these steps, you should be able to troubleshoot and fix the LED light flickering issue when connected to a dimmer switch.


Why is my dimmer switch flickering?

A flickering dimmer switch can be caused by incompatible light bulbs, loose wiring connections, or a faulty dimmer switch. It is important to troubleshoot and address the issue promptly to prevent potential electrical hazards.


How can I prevent flickering in my LED lights when using a dimmer switch?

To prevent flickering in LED lights when using a dimmer switch, make sure to use dimmer switches that are specifically designed for LED lights. Additionally, ensure that the dimmer switch is compatible with the wattage of the LED lights you are using. Upgrading to a higher quality dimmer switch may also help reduce flickering.


Why is the dimmer light flickering intermittently?

The dimmer light may be flickering intermittently due to a loose connection, a faulty dimmer switch, or incompatible light bulbs.


Why are the dimmer lights flickering in the room?

The dimmer lights are flickering in the room because there may be a loose connection in the electrical wiring or the dimmer switch itself. This can cause fluctuations in the flow of electricity, leading to the flickering of the lights.


Why are the LED lights flickering when connected to a dimmer switch?

LED lights may flicker when connected to a dimmer switch because some dimmer switches are not compatible with LED technology. This can cause the LED lights to receive inconsistent power, leading to flickering.


Can you use a dimmer switch on LED lights?

Yes, you can use a dimmer switch on LED lights, but it is important to make sure the dimmer switch is compatible with LED technology to avoid flickering or other issues.


Can a dimmer switch cause lights to flicker?

Yes, a dimmer switch can cause lights to flicker if not compatible with the type of bulbs being used or if the dimmer switch is malfunctioning. Flickering can also occur if the wiring connections are loose or damaged. It is recommended to use dimmer switches that are specifically designed for the type of bulbs being used to prevent flickering.


Why is my LED bulb flickering?

Your LED bulb may be flickering due to a loose connection, incompatible dimmer switch, or a faulty bulb.


Why is my LED light flickering?

Your LED light may be flickering due to a loose connection, incompatible dimmer switch, or a faulty LED driver. Check the connections, try a different dimmer switch, or replace the LED driver to fix the issue.


Why is my LED fixture flickering?

Your LED fixture may be flickering due to a loose connection, incompatible dimmer switch, or a faulty LED driver.


What are the benefits of using a trailing edge dimmer switch in a home lighting system?

A trailing edge dimmer switch offers benefits such as smoother dimming control, reduced flickering, compatibility with LED lights, and increased energy efficiency in a home lighting system.