0
Can you connect two 3 phase feed cables in parallel to one circuit breaker and if so what will the total output current be?
Wiki User
∙ 14y ago
The answer to the first part of your question is yes but the wire size has to be of a size specified in the electrical code for wires connected in parallel. As for the second part of the question the total current output is governed by the current draw of the load. It is the load current that governs the parallel wire size and the trip capacity of the breaker.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What will happen to the total current if you keep adding bulbs in parallel to the circuit?
Adding more lamps in parallel (across) a line will cause total current to climb. It will keep climbing (increasing) until a load protection device (circuit breaker or fuse) breaks the circuit or until something fails because of excessive current.
Rupturing capacity of a circuit breaker?
the maximum short current that can be safely break by the circuit breaker.
What circuit is a circuit in which electrical current has more than one path to follow?
A circuit that has more than one path for the current to flow is a parallel circuit. The circuit must have two or more paths to be considered parallel. A circuit that has only one current path through multiple components is a series circuit.
What is a difference between 10KA and 22KA circuit breakers?
The previous answer is incorrect, and I would advise that user to not give out information if they are going to give completely misguided information. The interrupting rating of a breaker is the maximum current that the breaker is designed to handle, at the breaker's rated voltage, before damage will occur to the breaker. A breaker will trip at FAR LESS than the interrupting rating, but it is extremely dangerous to expose the breaker to any situation where it will have more than the rated interruption current. the breaker is designed for. The reason some breakers are rated at 22kA instead of 10kA is because they typically have far larger conductors hooked up to them, so with the lowered impedance on the circuit there is more of a chance for the breaker to experience a higher fault current at the breaker. So electricians install 22kA breakers to handle the higher "available fault current."
How parallel and series circuit different?
In a series circuit, current has to pass through each part of the circuit. In a parallel circuit, the current has several alternative paths.
Is a circuit breaker a resistor?
No, a circuit breaker is a safety device that is used in a circuit to limit the amount of current in an overload or short circuit condition. The number on a breaker is the top end current that the breaker will handle before opening the circuit.
Will a circuit breaker give off less amperage?
A circuit breaker does not give off amperage. A circuit breaker allows a flow of current up to the rating of the breaker. Any current higher than that of the breaker's rating will open the breaker's contacts and stop the flow of current.
What are differences between series and parallel circuits?
In series circuits current will be the same through out the circuit. So whereever we connect the ammeter the same current is registered. But in parallel circuit current will be different in different lines. In parallel circuits the potential difference will be the same but in series pd will be different.
What will happen to the total current if you keep adding bulbs in parallel to the circuit?
Adding more lamps in parallel (across) a line will cause total current to climb. It will keep climbing (increasing) until a load protection device (circuit breaker or fuse) breaks the circuit or until something fails because of excessive current.
How do you install a resistor in an DC circuit?
It depends on the purpose for installing the resistor. If the intent is to decrease current flow, the resistor must be connected in series with the load. If the purpose is to increase current flow, the resistor must be connected in parallel with the load. To connect a resistor in series, connect the resistor to one side of the power source, in line with the load. This will decrease circuit current flow. To connect a resistor in parallel, connect the resistor between the positive and negative sides of the power source, which will effectively connect the resistor across the load . This will increase current flow through the circuit. However, before connecting a component in parallel, make sure the increase in current flow will not exceed the current rating of the circuit or fuses/breakers will blow.
Rupturing capacity of a circuit breaker?
the maximum short current that can be safely break by the circuit breaker.
What is a circuit with two or more branches for current to flow called?
Parallel circuit
What circuit is a circuit in which electrical current has more than one path to follow?
A circuit that has more than one path for the current to flow is a parallel circuit. The circuit must have two or more paths to be considered parallel. A circuit that has only one current path through multiple components is a series circuit.
What is the procedure to connect two circuits without losing the output voltage of first circuit which is transfered to the second circuit?
I assume you are talking about 120volt electrical circuits ???? If so, just wire them in parallel. In other words, connect the black wire to line side on each circuit and the white wire to neutral on each circuit. The bare ground wire goes to ground (green) At each circuit will be 120 volts AC. Do not exceed the maximum current of the circuit breaker supplying the current (typically 15 - 20 amps)
What is a difference between 10KA and 22KA circuit breakers?
The previous answer is incorrect, and I would advise that user to not give out information if they are going to give completely misguided information. The interrupting rating of a breaker is the maximum current that the breaker is designed to handle, at the breaker's rated voltage, before damage will occur to the breaker. A breaker will trip at FAR LESS than the interrupting rating, but it is extremely dangerous to expose the breaker to any situation where it will have more than the rated interruption current. the breaker is designed for. The reason some breakers are rated at 22kA instead of 10kA is because they typically have far larger conductors hooked up to them, so with the lowered impedance on the circuit there is more of a chance for the breaker to experience a higher fault current at the breaker. So electricians install 22kA breakers to handle the higher "available fault current."
Is the current the same everywhere in the parallel circuit?
No. The current in a series circuit is the same everywhere. The voltage across a parallel circuit is the same.
What is a switch that opens a cuircut when too much current is flowing?
Where I'm from, it's called a "circuit breaker".A circuit breaker.
