0
Can you control your mac using your Apple Built-In IR Receiver?
Wiki User
∙ 15y ago
The built in functions of the Apple remote are limited to a few applications. Software such as SofaControl (See links below) expands the functionality and it can be expanded further to your own requirements.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is the apple Lisa computer known for?
The Apple Lisa was the first commercially available computer with a Graphical user Interface and using a mouse as control.
How can one use Windows Media Center remotely?
Windows Media Center can be operated using a remote control. However a transceiver or infrared receiver is needed in order for the remote control to work properly.
Can you control the treble and bass controls in JVC surround sound speakers?
You can control the treble and bass in JVC surround sound speakers if the surround sound receiver you are using has treble and bass controls available.
Is the interface for Photoshop on a Mac different from the one on Windows?
Their essentially the same. The biggest difference is using of the Control("apple key") on the Mac with using the Ctrl key in Windows when using shortcuts
Can you get full screen photo booth on apple?
Just zoom in by holding down control, and zoom by using two fingers. http://ockdb.com
What is a sentence using receiver general?
You'll accept this cashier's check here and now, or the Receiver General will have your hide!
How do you make uncooked apple pie in Runescape?
You make an uncooked apple pie from using dough with a pie pan and using a cooking apple with the pan.
What would l be using if I was trying to tune into an AM or FM frequency?
You would probably be using a radio receiver. It is possible you'd be using a transceiver, which combines the functions of a transmitter and a receiver.
Can emails from apple be stopped when using find your phone?
Can emails sent by apple when using find my phone be stopped
How do you program a crafstman garage door opener 139.53879?
The SECURITY+ Universal Remote Control Conversion Kit consists of a receiver and remote control(s). This accessory will convert almost any garage door opener to rolling code technology. The remote control sends a coded signal from outside the garage. Inside the garage, the plug-in receiver accepts the transmitted signal and starts the door opener. With Security+, the code between the remote control and the receiver changes with each use, accessing over 100 billion new codes.PROGRAMMING THE RECEIVER The receiver and remote control(s) have been factory preset with a matching code. The door will open when you press the LARGE push button. You can activate your opener with up to eight SECURITY.I. remote controls (with blue push buttons) and one SECURITY+ Keylees Entry.If you purchase additional remote controls to operate this receiver: 1. Remove the receiver actuator cover. 2. Press and HOLD the selected remote control push button (Illustration A). 3. Then press the SRT (learn) actuator on the receiver (Illustration B). The adjacent indicator light will FLASH. Release the remote control push button. The opener will now operate when either the receiver actuator or the remote control push button is pressed. NOTE: If the remote control push button is not held down until the receiver Indicator light flashes, the receiver will not learn the code. To erase ALL remote control codes from memory: Press and HOLD receiver SRT actuator. Indicator light alongside will glow. When the Indicator light turns OFF (in about 6 seconds) ALL codes will be erased. 3-Function Remote Control A Select a remote control push button to operate receiver UnlversalReceiver SRT Actuator Light THE REMOTE CONTROL BATTERIES Open this end first to avoid cracking housing. Twist to open The lithium batteries should produce power for up to 5 years. Replace batteries positive side down, as follows: Use the visor clip or screwdriver blade to pry open the case as shown. To replace the cover, insert the 3 tabs at the opposite end and snap shut.Make sure you are using security plus remotes with blue buttons. Simply press and hold the button on the remote and then press the srt learn button on the receiver and the light bulb should flash. If this does not work you either have a bad remote, receiver or wiring. Make sure the wiring is good and hooked up to the push button terminals.
How do you die using an apple?
you choke on it.
Is apple still using slave labor?
Apple never used slave labor
