0
Yes, if you have the special blade to do so. I use Bosch or Lenox blades with 32 teeth per inch
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What saws to use for cutting out wood patterns jig saw and router saw?
Obviously A router is NOT a saw. -To cut patterns use a jig saw or a scroll saw.
What is a relief cut in woodshop?
A preliminary cut with a jig saw or band saw to prevent the saw from binding, when cutting a curve in a piece of wood.
What can you use to cut plexiglass?
jig saw and a plastic bit or one with lots of teeath
What saw cuts on the backstroke?
I'm not being smart, a backstroke saw. There are Japanese saws that cut both ways. There is a blade for a jig saw that cuts on the up stroke for cutting laminate from underneath so it doesn't chip.
What is uses of jig saw?
A jig saw is used mainly in carpentry for cutting lumber in ways or patterns that require tight turns or intricate designs. Example: to cut out a hole for a sink basin in a counter-top you need a jig-saw to be able to cut those rounded corners that will contour with the sink basin.
How do you cut stainless steel?
Depending on the thickness and how nice you want the finished edge to look, steel can be:sawedshearedcut with an oxy-acetylene torchcut with a plasma cuttercut with a water-jetcut with an abrasive wheelcut with snips
How do you cut holes in ceiling tiles?
Holes can be made with a knife, drywall keyhole saw, jig saw or appropriately sized drill bit.
How to Cut Stainless Steel Tubing?
If you are doing a building project at home or elsewhere, chances are at some point you're going to have to use stainless steel tubing. Stainless steel tubing is a very resilient material to use for projects that require piping. However, you may be new to using it. If you are, read the steps listed below to learn how to cut stainless steel tubing.There are basically two methods you can use to cut stainless steel tubing. You can use a tube cutter or an abrasive cutoff saw. Using a tube cutter is best suited for stainless steel tubing that has relatively thin walls.To use a tube cutter, start by opening up the cutter's jaws. You can do this by cranking the handle counterclockwise. Place the opening of the curved blades over the part of the tube you want to cut. Use a pencil to mark this spot ahead of time.Now you will do the actual cutting. Do so by cranking the cutter's handle clockwise. As the handle cranks, the blades will close in and cut into the tubing. When the blades touch the tube the first time, stop cranking the handle. Next, crank the handle of the cutter once all the way around in a single movement.As you continue cranking the handle, tighten it by a half a crank for each revolution that the cutter makes around the tube. Keep doing this until you are finished cutting.An abrasive cutoff saw should be used to cut stainless steel tubes with thick walls. You should only attempt to use a cutoff saw on a piece of stainless steel tubing after it has been placed in a vise. You should also wear eye goggles and thick gloves for protection.After you turn on the saw, move it very slowly over the tubing as you cut it. Do not force the saw down into the tubing. You should let it cut slowly for safety reasons and to get the cleanest cut. You should also be careful when you remove the cut pipe. The cut metal will be extremely hot.If there is any clinging metal left after the sawing, use a metal file to file it clean.
In fcaw process in stainless steel weld lof occuswhy?
IN SAW WHY SLAG OCCURS?
What power tool is used to cut metals?
an angle grinder,nibblers,band saw,circular saw,mitre saw,jig saw, all of these need metal cutting blades as some of them can cut wood aswell depending on the blade
What metal is a saw made of?
All saw blades are made from steel. Sometimes handles are steel too, but more often, wood, plastics or hard rubber.
What saw blades cuts stainless steel?
You need an 'abrasive fibre cutting disc', rather than a saw. I usually have one in my small angle grinder for cutting steel.
