answersLogoWhite

0

Cast Iron pipe can SOMETIMES be fixed by coupling it to the pipe using a rubber coupling and worm clamps. This rubber coupling is sometimes referred to as a "rubber boot". You should always check your local Plumbing code first to see if what and where you are replacing can be remedied by this method. You would first need to cut the cast iron pipe section out which you want replaced. There are a few different devices and blades made to achieve this depending on what tools you have access to. The most basic can be found at your local home improvement center or plumbing supply house such as a reciprocating saw blade meant for cast iron. Once the section of pipe is out, you should be able to maneuver the boot or boots and pipe into place and tighten the clamps to fit snugly around the cast iron and PVC. The days of oakum and leading cast iron pipes is long gone :)

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How can I fix a broken PVC pipe?

To fix a broken PVC pipe, you can cut out the damaged section using a hacksaw, clean the ends of the pipe, and then use PVC primer and cement to attach a new piece of PVC pipe or a coupling to the existing pipe. Make sure to follow the manufacturer's instructions for the primer and cement for a secure and leak-free repair.


How can I fix a leaking PVC pipe joint?

To fix a leaking PVC pipe joint, you can try tightening the joint with a wrench, applying PVC primer and cement to reseal the joint, or replacing the joint if it is damaged beyond repair.


Is there a way to fix a PVC pipe leaking in my home?

Yes, you can fix a leaking PVC pipe in your home by first identifying the source of the leak, then turning off the water supply, drying the area around the leak, and applying a PVC pipe repair kit or using PVC cement to seal the leak.


Explain how you can fix a leaky PVC water pipe?

Brake it down


How can I fix a broken PVC water pipe outside?

To fix a broken PVC water pipe outside, you can follow these steps: Turn off the water supply to the pipe. Cut out the damaged section of the pipe using a PVC pipe cutter. Clean and dry the ends of the remaining pipe. Apply PVC primer and cement to the ends of the pipe and the replacement section. Connect the replacement section to the existing pipe and hold in place for a few seconds. Allow the cement to dry completely before turning the water supply back on.


How do you fix a leaking cast iron stack pipe that is not accessible because it is in the wall?

Demo a section of the wall.


How can I fix a PVC pipe leak?

To fix a PVC pipe leak, you can use a PVC pipe repair kit or epoxy putty to seal the leak. First, turn off the water supply to the pipe. Clean and dry the area around the leak, then apply the repair material according to the kit's instructions. Allow it to dry completely before turning the water back on.


How can I fix a hole in a PVC pipe?

To fix a hole in a PVC pipe, you can use a PVC pipe repair kit or epoxy putty. First, clean and dry the area around the hole. Then, follow the instructions on the repair kit or epoxy putty packaging to apply the material over the hole. Allow it to dry and cure according to the instructions before using the pipe again.


How do you fix a leaking pipe cast iron stack pipe that is not accessible because it is in the wall?

You must break or cut the wall at that point. No other option


How do fix a leaking cast iron stack pipe that is not accessible?

You pretty much have to open up the wall. If you had access to the ends above and below the wall I suppose you could cut the pipe and put a 3 inch pvc inside of it if there were no branches in the pipe, but that isn't likely. There just isn't any way of fixing it without opening the wall.


How can I fix a PVC pipe leak efficiently and effectively?

To fix a PVC pipe leak efficiently and effectively, you can follow these steps: Turn off the water supply to the pipe. Clean the area around the leak with a rag and some sandpaper. Apply PVC primer and cement to the pipe and fitting. Quickly insert the fitting into the pipe and hold it in place for a few seconds. Allow the cement to dry for the recommended time before turning the water back on.


How can I fix a leaking PVC pipe in my plumbing system?

To fix a leaking PVC pipe in your plumbing system, you can follow these steps: Turn off the water supply to the affected area. Dry the area around the leak with a towel. Use a PVC pipe cutter to cut out the damaged section of the pipe. Clean the ends of the remaining pipe with sandpaper. Apply PVC primer to the ends of the pipe and the inside of a PVC coupling. Apply PVC cement to the primed areas and quickly connect the coupling to the pipe ends. Hold the connection in place for a few seconds to allow the cement to set. Turn the water supply back on and check for any leaks. If the leak persists, you may need to seek professional help.