The short answer is no. First off I assume you mean "can you have a dryer and an electric range on the same circuit?" (If they were actually wired in series, then you couldn't use your range if the dryer was off) In theory you could have them on the same circuit you just need to make sure that the wiring and the circuit they are on can handle the number of amps the two of them could draw together. If your breaker isn't big enough, it kill the power to the range while you are cooking dinner. If the wiring can't handle the load, then there is a fire risk. A dryer is usually on a 30amp circuit and a range is usually on a 50amp circuit, so to have them together would require an 80amp circuit, which will be difficult to find a breaker and wiring for.
Not normally, the pins are in a different configuration.
== == A dryer outlet is only safe to use for one purpose: to power a dryer.Obviously you can attempt to use it for something else, such as an electric range, but it is NOT SAFE to do it!You could drive on the wrong side of the road but it is NOT SAFE to do it!You could put your hand into a fire but it is NOT SAFE to do it!In general the reasons for saying it is not safe to use something other than a dryer on a dryer outlet are all about being sure that the circuit you will use for the other appliance (in this case an electric range) has: * the right size of wires to carry the current the appliance takes and* the right size of breakers on the main supply panel to protect the appliance - and the wiring to it - from catching fire if there is ever a malfunction. Electric ranges are quite different to dryers: people are likely to be "in close attendance" to them all the time they are on! You have to be sure you wire them up correctly and safely to avoid there being any kind of risk of anyone getting electrocuted.You also have to be sure that the supply circuit used is of the right kind to protect the house from a house fire. That can happen if there is a malfunction in the range but the circuit breakers on the main supply panel - or the wiring feeding it - are the wrong size. The circuit breakers on the main supply panel - and the wiring feeding the outlet for the range - must all be properly sized and correctly and safely installed. == == For more information please see the Related Questions shown below. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Probably not. The reason is the amperage required by the electric range. They typically require 50 amp whereas a dryer normally only requires 30 amp. Therefore, the wiring feeding the dryer is not large enough to support an electric range. Your range should be wired with #6 or 8 gauge wire, whereas your dryer is likely only wired with # 10 gauge which will not carry 50 amps.
A resonator is a circuit that responds to a narrow range of frequencies. A typical resonator is a tuned circuit containing an inductor and a capacitor in series or parallel. A series connected tuned circuit has zero impedance at the resonant frequency, while a parallel tuned circuit has infinite impedance at the resonant frequency. The resonant frequency in both cases depends on the inductance times the capacitance: F = 1 / (2.pi.sqrt(LC)) If the inductance is in Henrys and the capacitance in Farads, the answer is in Hz.
No. The two appliances usually have dedicated circuits. The range will have a two pole 40 amp breaker and be fed with a 3-C #8 copper cable. The dryer will have a 30 amp two pole breaker and be fed with a 3-C # 10 copper cable. As you can see by powering a 40 amp device from a 30 amp breaker, full operation of the range will trip the 30 amp breaker.
Not normally, the pins are in a different configuration.
the voltage of the mains electricity in the UK
240V appliances, such as range, dryer, air conditioner.
== == A dryer outlet is only safe to use for one purpose: to power a dryer.Obviously you can attempt to use it for something else, such as an electric range, but it is NOT SAFE to do it!You could drive on the wrong side of the road but it is NOT SAFE to do it!You could put your hand into a fire but it is NOT SAFE to do it!In general the reasons for saying it is not safe to use something other than a dryer on a dryer outlet are all about being sure that the circuit you will use for the other appliance (in this case an electric range) has: * the right size of wires to carry the current the appliance takes and* the right size of breakers on the main supply panel to protect the appliance - and the wiring to it - from catching fire if there is ever a malfunction. Electric ranges are quite different to dryers: people are likely to be "in close attendance" to them all the time they are on! You have to be sure you wire them up correctly and safely to avoid there being any kind of risk of anyone getting electrocuted.You also have to be sure that the supply circuit used is of the right kind to protect the house from a house fire. That can happen if there is a malfunction in the range but the circuit breakers on the main supply panel - or the wiring feeding it - are the wrong size. The circuit breakers on the main supply panel - and the wiring feeding the outlet for the range - must all be properly sized and correctly and safely installed. == == For more information please see the Related Questions shown below. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Probably not. The reason is the amperage required by the electric range. They typically require 50 amp whereas a dryer normally only requires 30 amp. Therefore, the wiring feeding the dryer is not large enough to support an electric range. Your range should be wired with #6 or 8 gauge wire, whereas your dryer is likely only wired with # 10 gauge which will not carry 50 amps.
A resonator is a circuit that responds to a narrow range of frequencies. A typical resonator is a tuned circuit containing an inductor and a capacitor in series or parallel. A series connected tuned circuit has zero impedance at the resonant frequency, while a parallel tuned circuit has infinite impedance at the resonant frequency. The resonant frequency in both cases depends on the inductance times the capacitance: F = 1 / (2.pi.sqrt(LC)) If the inductance is in Henrys and the capacitance in Farads, the answer is in Hz.
No. The two appliances usually have dedicated circuits. The range will have a two pole 40 amp breaker and be fed with a 3-C #8 copper cable. The dryer will have a 30 amp two pole breaker and be fed with a 3-C # 10 copper cable. As you can see by powering a 40 amp device from a 30 amp breaker, full operation of the range will trip the 30 amp breaker.
I don't think you quite understand your question. If this is new construction, (or redesign), and you are installing a gas range, the gas line has to be installed to code. If you are abandoning already installed electrical wiring, you should either remove the wiring and the circuit breakers or securely seal the ends of the wires with wire nuts and tape and turn off the circuit breakers. It also helps to lable the wires and circuit breakers as "old - not in use".
industry standard practice. the electrical load from a combination range is the same as the combined loads from a wall oven and countertop. so your panel and electric service will handle it. BUT the range will be on a single circuit and you must ensure that the range circuit requirements are met. the circuit requirements are on the nameplate. for example, if the range requires a 30 amp circuit and your wall oven was a 30 amp circuit then you can use the wall oven circuit. but if the range requires a 40 amp circuit, then you have to pull a 40 amp circuit from the panel to the range.
No, unless it's a gas range. An electric range requires 240V and 40A while a small appliance will be 120V and Max 15A.
s for USA, Canada and countries using similar 60Hz mains suppliesYou did WHAT? There is no way it is safe for two things that each can take a heavy load, like a range and a dryer, a) to be wired onto a circuit that was originally installed just for a dryer and b) actually be used at the same time.You are well on the way to burning your house down.Note: In some localities what you have done may actually be ILLEGAL.Always consult a licensed electrician before you do anything like this!A dryer outlet is only safe to use for one purpose: to power a dryer.Obviously you can attempt to use it for something else, such as an electric range, but it is NOT SAFE to do it!You could drive on the wrong side of the road but it is NOT SAFE to do it!You could put your hand into a fire but it is NOT SAFE to do it!In general the reasons for saying it is not safe to use something other than a dryer on a dryer outlet are all about being sure that the circuit you will use for the other appliance (in this case an electric range) has:the right size of wires to carry the current the appliance takes andthe right size of breakers on the main supply panel to protect the appliance - and the wiring to it - from catching fire if there is ever a malfunction.You also have to be sure that the supply circuit used is of the right kind to protect the house from a house fire. That can happen if there is a malfunction in the range but the circuit breakers on the main supply panel - or the wiring feeding it - are the wrong size. The circuit breakers on the main supply panel - and the wiring feeding the outlet for the range - must all be properly sized and correctly and safely installed.As you asked this question here, the best thing you can do to be able to use your electric range with no worries is to ask a licensed electrician for his advice. He can also quote you for installation of the correct type of outlet, wiring and breakers on the main supply panel to power your new range safely.For more information please see the Related Questions shown below.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicator to insure the circuit is, in fact, de-energized.
The 54 series are military specification versions with a greater operating temperature range.