0
Can you put 2 circuits on one neutral in a single phase house panel?
Wiki User
∙ 12y ago
you can, but i would not recommend it, I've seen it done many times in older homes, if for some reason you do make sure both circuit power"hot" wires are connected to the same bus of electrical panel or a backfeed could cause a high voltage and be even more hazardous
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Can you use 3 phase circuit as 3 separate single phase circuit?
yes we can use as a single phase circuit because at practise directly the 3-phase circuit is made by combining the three single phase circuits
What is a single phase panel?
The term, single-phase 'panel', describes an electricity distribution panel (called a 'consumer unit' in the UK) comprising line, neutral, and earth (ground) busbars, supplying a number of circuits which are each protected with either a fuse or a miniature circuit breaker. The panel normally incorporates an isolation switch that will disconnect the busbars from the supply system. The panel is fed from the utility company's supply system, via a fuse and energy meter.
What is an electric shared neutral?
An electric shared neutral is the white or negative wire that is shared between two electrical circuits on a basic single phase system. Most electrical devices use 120 volts and require a "hot" wire and a neutral wire to operate. Some larger devices use 240 volts and require two "hot" wires to operate. Two circuit breakers in an electrical panel can share one neutral wire as long as the breakers are not on the same "leg" of power. When looking at an electrical panel there are usually two "legs" of power feeding all the breakers, each leg has 120 Volts to ground, if the "legs" are combined you will have 240 Volts. A neutral wire can be shared by two circuits as long as the breakers are on separate "legs". If someone needed to add two circuits in their home, the could run what is called a 3-wire romex, It has a black wire, a red wire, a white wire and a ground wire. The white wire is the neutral for both the black and red 120 volt circuits, and the breakers for the new circuits would need to be on separate "legs" in the panel.
How do you wire floating neutral in sub panel?
You need to be more specific. Is this your feed?? Is this a home run (the wire that is feeding a circuit). Anyway if this is your feed wire (the wire supplying power to your sub panel) then you will land your two hots , then you will land your ground wire on the lug that is bonded to the panel. Sometimes this is a ground bar that can be screwed to the panel itself and then your neutral will go to the bar that is not touching anything. So your neutral coming in will be tightened down to the same bar as the neutrals that are feeding the circuits. This is assuming you'r are feeding your sub panel with 2 hots, a ground and a neutral.
How do you add a circuit when panel is full?
That depends on the manufacturer of the breaker panel. Some manufacturers sell dual breakers that can be plugged in where one of your single breakers are now. You can also do an audit of current panel, ideally by a qualified electrician. You may have unused or underused circuits. For example if you had two 15A circuits that had a maximum aggregate usage of 5A, you could splice those circuits external to the main panel in a junction box (and wire to one breaker) and use the leftover breaker for your new circuit. In any solution you need to ensure that your panel service is compatible with the loads in your house. In some cases you may need to increase the size of your panel. Consult an electrician and ask for a free estimate.
If you are making your own device and you bring in 208 3 phase for part of your needs - how can you properly tap 110 single phase from it to operate other parts of your device?
Your incoming 208V 3 phase power supply will also need an incoming neutral of the same conductor size. Then any single pole breaker installed in the panel will have 110 volts to the neutral. That is you can run 208V 3 phase motor circuits from a three phase breakers in the panel and any number of 110V circuits from single pole breakers.
Can you use 3 phase circuit as 3 separate single phase circuit?
yes we can use as a single phase circuit because at practise directly the 3-phase circuit is made by combining the three single phase circuits
What is a single phase panel?
The term, single-phase 'panel', describes an electricity distribution panel (called a 'consumer unit' in the UK) comprising line, neutral, and earth (ground) busbars, supplying a number of circuits which are each protected with either a fuse or a miniature circuit breaker. The panel normally incorporates an isolation switch that will disconnect the busbars from the supply system. The panel is fed from the utility company's supply system, via a fuse and energy meter.
Why isn't there a ground in a junction box?
Only the main panel is grounded directly because if you ground each junction box of subpanel ground loop current paths are possible that can cause shock hazards. The ground rod is connected to main panel and the neutral is bonded to that ground as is the ground wire. The neutral and ground wire are then run to all circuits, junction boxes and subpanels throughout the house. If you tie neutral and ground together at any point in the house, other than the main panel ground loops can exist and cause shocks.
Can you use a GFCI on an unswitched circuit line red that uses the same neutral white for a switched circuit coming from the other phase line black in a 240v breaker panel?
Yes. You are allowed to use a neutral for one circuit from each phase of your service. For example, in a residential service, you can use the same neutral for circuits 1 and 3. In a commercial (3 phase) service, you can use a neutral for circuits 1, 3, and 5. You will experience problems if you use a neutral for two 'black' circuits or two 'red' circuits, if the circuits originate from the same phase bus bar. Also, AFCI's are sensitive to sharing neutrals, but GFCI's are not.
What is an electric shared neutral?
An electric shared neutral is the white or negative wire that is shared between two electrical circuits on a basic single phase system. Most electrical devices use 120 volts and require a "hot" wire and a neutral wire to operate. Some larger devices use 240 volts and require two "hot" wires to operate. Two circuit breakers in an electrical panel can share one neutral wire as long as the breakers are not on the same "leg" of power. When looking at an electrical panel there are usually two "legs" of power feeding all the breakers, each leg has 120 Volts to ground, if the "legs" are combined you will have 240 Volts. A neutral wire can be shared by two circuits as long as the breakers are on separate "legs". If someone needed to add two circuits in their home, the could run what is called a 3-wire romex, It has a black wire, a red wire, a white wire and a ground wire. The white wire is the neutral for both the black and red 120 volt circuits, and the breakers for the new circuits would need to be on separate "legs" in the panel.
In ac single phase circuits what is the neutral for?
The neutral in single phase AC circuits is used as the common power return conductor for half phase operation. In a typical (US/Canada) 120/240 split phase system, generally used in residential applications, the voltage between neutral and either of the two hot conductors is 120 VAC, and the voltage between the two hot conductors is 240 VAC. Neutral is also grounded at the distribution panel, as well as at the utility distribution transformer, in order to limit the voltage of any conductor relative to ground, and also to be able to detect ground faults by sensing imbalance between neutral and hot currents. Note that this is not called two phase power. It is single phase, or split phase, and it comes from one center tapped transformer winding. The center tap is neutral.
How do you wire floating neutral in sub panel?
You need to be more specific. Is this your feed?? Is this a home run (the wire that is feeding a circuit). Anyway if this is your feed wire (the wire supplying power to your sub panel) then you will land your two hots , then you will land your ground wire on the lug that is bonded to the panel. Sometimes this is a ground bar that can be screwed to the panel itself and then your neutral will go to the bar that is not touching anything. So your neutral coming in will be tightened down to the same bar as the neutrals that are feeding the circuits. This is assuming you'r are feeding your sub panel with 2 hots, a ground and a neutral.
How do you add a circuit when panel is full?
That depends on the manufacturer of the breaker panel. Some manufacturers sell dual breakers that can be plugged in where one of your single breakers are now. You can also do an audit of current panel, ideally by a qualified electrician. You may have unused or underused circuits. For example if you had two 15A circuits that had a maximum aggregate usage of 5A, you could splice those circuits external to the main panel in a junction box (and wire to one breaker) and use the leftover breaker for your new circuit. In any solution you need to ensure that your panel service is compatible with the loads in your house. In some cases you may need to increase the size of your panel. Consult an electrician and ask for a free estimate.
How do you install a 110v receptacle from a 3 phase breaker box if there are no neutrals in the breaker box?
If there is no neutral available you cannot, unless you use an autotransformer and derive a neutral. A panel with no neutral is called a power panel and is used to supply 240 single and three phase loads.
Why Hot and neutral are both hot?
You'll have to explain your problem better.If HOT black and Neutral White in your house wiring are both hot then Neutral is NOT bounded to ground in main panel and neutral could be floating. There should be no voltage between Neutral and Ground (Bare wire in panel). By code if there are multiple panels Ground is only bonded to Neutral in th emain entry panel. I have seen cases where this bonding was not done. At your main panel check voltage between neutral and ground. It should be zero.
Does a 480 volt panel have a neutral bus?
Usually yes. A typical 480 volt panel is a 3 phase panel with 480 volts line-to-line and 277 volts line-to-neutral. However, I did once see a panel that was 480 volts, 3 phase, but because it served only motors it did not have a neutral. (a 3 phase motor doesn't use a neutral.) Similarly, if a panel uses only 2 legs of a 3 phase 480 volt system, which would be called single phase, it would not require a neutral if it only feeds 480 volt single phase loads. But I find the idea of no neutral to be extremely unusual and in my one personal experience, I blamed it on the age of the system. In 16 years of commercial and industrial construction I have never installed a 3 phase panel without a neutral and all my work is designed by engineers.
