0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you disconnect remote starter?
To disconnect a remote starter you will have to remove the dashboard panel around the car's steering column. Look for the remote starter. Disconnect the wire at the starter that goes to the positive battery terminal. Put the dashboard panel back on.
How do l put a starter bypass switch in a 1975 Chevrolet pickup?
You can jump start an older vehicle like this by shorting out the starter and solenoid with a screwdriver being careful to use one that doesn't ground you. You must have the vehicle switch to on. If you cannot get the vehicle to switch on you can hotwire the wire to the distributor to the battery. Not the safest way but in an emergency. A better way is to get a remote starter switch and wire it to the starter per its instructions. This is not to be confused with one of the newer remote starters which must be patched into the vehicles ignition and fuse box. You can also wire an ignition switch, preferably with an inline fuse, to the starter as well. This is a DIYer so if you have no electrical/mechanical training or experience then I'd get someone to help you. Good luck.
I am trying to put a remote starter in my 2003 Rav4 and I can't find the coil ---- Where is it --- Also is the high votage coil starter the same as the high coil?
02 to 04 RAV's got individual computer controlled coils your remote starter has to conected to the ignition assembly in the steering cullum.
Is it illegal to put a remote starter on a manual transmission car?
no its not illegal in most states. check with your dept. of transportion
I bought a used car with a remote starter after I start it and I get in the vehicle what do I do next?
Once you get in, depending on how old the vehicle is, you can depress the brake pedal and it will shut the vehicle off, or on newer models, you can push the hazard button, and that will do the same thing. Once your vehicle is started and you want to take off, you must put the key in the ignition, and turn it on, but DON'T CRANK THE ENGINE OVER!!
Do you need a transponder for your ford windster to put in a remote starter?
No you don't, when you install a remote start, it will come with a transponder for it, if you go to get it installed at a place like bestbuy it will come with a remote start transponder after they install it for you. Imad
Can you put a remote start on a throttle-body engine?
Yes, as long as the vehicle has an automatic transmission.
How do you put in a new starter on a 1993 F250?
Disconnect - battery terminal Raise and support vehicle Loosen and remove mounting bolts Drop starter Remove wiring from top of starter
What are some of the best lease deals for a new vehicle?
Right now, Volkswagen is having the sign and drive event where you put no money down at lease. Other car companies such as VW are making your first payment for you.
How to change a starter?
The starter is usually located on the passenger of the vehicle, under and to the rear of the engine where it bolts to the flywheel housing. Steps for changing a starter: (1) disconnect the negative cable at the battery; (2) raise the vehicle and put jackstands under it for support (3) block the rear tires to keep vehicle from rolling backwards; (4) under the vehicle, disconnect the red cable and the black wire that connect to the starter solenoid; (5) unbolt and remove the two bolts that attach the starter to the flywheel housing; (6) pull starter out. Installation is reverse. Good luck...
Where are remote car starters located?
Most remote car starters are located in the bottom of the dash board, usually under the steering column. Some newer cars with remote starters built in may have the starter in a location other than in the dashboard, but if you are installing the car starter yourself, you will most likely put at the bottom of the dashboard unless instructions indicate otherwise.
How do you change the starter on a 1985 Mercury Topaz?
Disconnect the battery. The vehicle will probably have to be raised to reach the starter. The starter has two or three bolts holding it in, and wiring attached. Remove the wires remembering where to put them back. Remove the bolts and pull starter out.
