Yes, generally, all other things being the same.
By all other things I mean the capacitance, the type of capacitor for the application, etc.
If the motor is rated at 370 v and the supply is 370 v, the capacitor needs to be rated at 370 or more volts, so a 440 v capacitor will be OK.
The difference is that the 440 vac capacitor has a 70 volt-amp-current higher output than the 370. Capacitors must always be replaced with the same size micro-farads or you'll damage the device, such as a motor. The vac rating can be changed with a capacitor with a higher rating but not lower. Example: 15mfd at 370vac can be replaced by a 15mfd at 440vac, but not the opposite.
The 440 volts listed on the cap is the maximum allowable voltage the capacitor can handle. You could actually use a 370 volt cap on 230 volts. ANSWER; 230 volts AC can it actually be 644 volts peak to peak . It is 44ov because it must be rectified and sees only 324 volt peak which is withing the 440 volt capacitor handling voltage
Part# 43-25133-03 (Dual Round). Part#43-25135 (Dual Oval). Both listed are OEM parts Rated 35/3 MFD - 370 VAC
Because when a fan motor (or compressor), is designed to operate on a 370 VAC run capacitor, that will be its optimal efficiency operating design. We're talking about capacitors used on an A/C in a typical 230 volt power supply to a residence or business. If you substitute a 440 VAC run cap in place of the 370 cap, the motor will seem to operate just fine. However, if you put an amprobe on the motor, you will find an increase in the amps it is drawing. This translates to increased heat in the windings, and some motors can handle a small heat rise while others have a problem with it. It partly depends on the airflow over the fan motor along with the quality of the motor, but in any event, you are decreasing the life of the motor along with paying for the electrical current you're wasting, and also, not using the specified cap the motor calls for, in most cases, will void the motor's warranty. The worst place to substitute a 370 VAC cap with a 440 VAC cap is on a compressor. The increased heat load in the windings causes an increase in head pressure and on some compressors already operating at high head pressure and heat load, the compressor can trip off and will stay off until the shell cools down. Of course, the additional amp draw in the compressor will really drive up the power bill. Bottom line, use the cap the motor specs call for. If you have to substitute to get-by because you don't have the right one on your truck, go back the next day and put the right one in. George Henne--Retired A/C Tech----
If the motor is rated at 370 v and the supply is 370 v, the capacitor needs to be rated at 370 or more volts, so a 440 v capacitor will be OK.
You can always use a higher voltage rated capacitor, it will probably just last a little longer.
There are two ways to read this: you have a burned-out run capacitor on your motor and a good start capacitor in your parts box, and you have a burned-out start capacitor and a good run capacitor. If the run capacitor's bad and you want to put the higher-voltage start cap in its place, the answer is yes. This is called derating, and the only thing it does for you is increases the lifespan of the capacitor because you're not working it as hard as it can take. If the start capacitor's bad, don't do this--they used a 440-volt capacitor in there for a reason.
An AC capacitor is composed of two DC capacitors with the foil ends (-) connected together and the center ends (+) connected to the outside. There are variations to the connections. Each capacitor has to have the voltage rating required by the application -- and there are two capacitors in series in an AC capacitor. A 230V AC capacitor, depending on manufacturing design standard, may not be suitable for starting a 230V air conditioner.
The difference is that the 440 vac capacitor has a 70 volt-amp-current higher output than the 370. Capacitors must always be replaced with the same size micro-farads or you'll damage the device, such as a motor. The vac rating can be changed with a capacitor with a higher rating but not lower. Example: 15mfd at 370vac can be replaced by a 15mfd at 440vac, but not the opposite.
The draft boost blower for the Fasco Motor is available as a furnace repair replacement part. It has single speed at 3000 RPM with sleeve bearing. This blower is for heaters, oil and gas furnaces. It operates on 115 volts with 0.7 amps. There are also different kinds of capacitors that can be replaced. The 10m - 370 volt, oval motor run capacitor or the 440 VAC, dual round capacitor can be used as replacements.
The 440 volts listed on the cap is the maximum allowable voltage the capacitor can handle. You could actually use a 370 volt cap on 230 volts. ANSWER; 230 volts AC can it actually be 644 volts peak to peak . It is 44ov because it must be rectified and sees only 324 volt peak which is withing the 440 volt capacitor handling voltage
Not a good idea, without knowing more about the circuit in which it's installed. Presumably, the 440v capacitor was selected because its max voltage rating (440v) is higher than the instantaneous voltage to be expected at that point in the circuit. By that criterion, the voltage at that point in the circuit may exceed 370 volts, and your proposed replacement component won't hold it.
In most cases, yes. Unless you're in some high precision device, you're probably working with a 5-10% tolerance which would allow a 15-30 microfarad variance. Even a 1% tolerance would give you 3 microfarads. You can go with the same or higher voltage rating, just not lower.
Part# 43-25133-03 (Dual Round). Part#43-25135 (Dual Oval). Both listed are OEM parts Rated 35/3 MFD - 370 VAC
if you have a 370, the oil capacity is zero, run it till it blows, a replace with a better engine. the 370 is junk.
250