It is not recommended. The design of the equipment called for the 315ma fuse. To up size it to a larger fuse is taking the equipment out of its manufactured specification.
Fuses are used to protect circuits. If you install an oversized fuse you override the designed in protection.
Another 750 mA fuse. 750 mA is equal to .75 amps. The max I would put in is a 1 amp fuse and I would want to replace it soon with the proper one.
It is a fuse that is rated in one thousandths of an amp. An example, a 500 mA fuse can also be called a 1/2 amp fuse.
It's the standard Type 'G' 3-pin plug used in the UK for electrical equipment and appliances. It should always contain a cartridge fuse of the right size to match the current or "amperage" drawn by the equipment/appliance it is supplying with power. Standard fuses to fit the plug are available in 13 amp, 5 amp, 3 amp and 1 amp sizes. For more information see the Related Link and the answer to the Related Question shown below.
Amp, Amperes is current. Volt, and any variation, is tension. There's no direct translation between them.
25mm cable
Surely you have had too much eggnog. A fuse is designed to blow if the rated current is exceeded. So the answer is definitely no. If there were such a thing as a million amp fuse you would need a giant crane to even lift it.
No, the one amp fuse is the recommendation of the manufacturer of the circuit. By replacing it with a fuse five times larger will default the warranty placed on the equipment by the manufacturer. Where one amp will do no damage to the circuit, five amps could destroy the components that are connected in the circuit.
1 amp
Another 750 mA fuse. 750 mA is equal to .75 amps. The max I would put in is a 1 amp fuse and I would want to replace it soon with the proper one.
fuse number 1 is 10 amp fuse 2 is 25 amp fuse 3is 25 amp fuse 4 is a spare fuse 5 is 10 amp fuse 6 is a spare fuse 7 is 20 amp fuse 8 is 25 amp fuse 9 is 20 amp fuse 10 is 5 amp fuse 11 is 5 amp fuse 12 is a spare fuse 13 is 5 amp fuse 14 is 15 amp
It is a fuse that is rated in one thousandths of an amp. An example, a 500 mA fuse can also be called a 1/2 amp fuse.
Yes you can do that as long as it will fit in the fuseholder. It is acceptable to replace a lower Voltage Rated fuse with a higher but NEVER replace a higher with a lower. There are several things to consider when replacing a fuse: 1) The minimum voltage rating of the fuse is equal to or higher than the voltage of the circuit you are placing it in 2) The Amperage rating of the fuse does not exceed the capacity of the circuit you are trying to protect. Always replace a fuse with one that has the same amperage rating. 3) The interrupting rating of the fuse is sufficent for the capacity of the circuit supplying the fuse. If replacing a fuse always use one with an interrupting capacity equal to or greater than the fuse you are replacing.
you replace the bad 1
The 30 amp fuse is located under the left side cover in a 1-1/2"x2" fuse box alomg with 3 other fuses.
In the Power Distribution Box ( which is " live " ) in the engine compartment : Mini fuse # 1 is a 30 amp fuse for the PCM relay Mini fuse # 2 is a 10 amp fuse for the PCM and front electronics module Mini fuse # 5 is a 15 amp fuse for the PCM and fuel pump motor
fuse # 1 20 amp fuse in Central Junction Box
Fuse # 1 is a 20 amp fuse for the cigarette lighter on a 1998 Ford Mustang