0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Can you hook both a subwoofer and speakers to 1 amp If so do I need to buy a amp that's even more powerful Then what the sub requires?
You can connect a sub and speakers to one amp, depending on how many channels your amp has. A 4 channel amp will be able to run one (or two) subs using two channels (one bridged* sub or two subs) and two speakers running one channel each. A 2 channel amp will run 2 speakers or one bridged sub. A 6 channel amp will run one bridged sub (or two subs), 2 front speakers and 2 rear speakers. In my opinion, you will get the most performance, depending on which amps you use, by using a monoblock amp for your sub and an amp with enough channels to run all of your speakers. # Bridged = putting together the power of two channels to run one sub or speaker. Note: not all amps are bridgeable.
Bridge two subs to a four channel amp?
If you amp is bridgeable you run + sub wire to ch 1 + then the -sub wire to the - of ch 2 of the amp. The same with the other sub + ch3 - ch4 that's how to bridge your amp.
How do you know if your amp is putting out one channel or two channels?
It will say mono if its only 1 channel which is a sub amp only.
How do you connect two amps to four subs?
Run a 2 sub per amp set-up. Get a distribution block for you power wire to split the power wire. You can run the remote wire from your stereo to one amp and then from the amp to the other amp. you will also need 2 sets of RCA's Easy way is too get a 4 channel amp to power 4 subs.
What is a two channel amp?
A two channel amp, in simple terms, means that it amplifies two different inputs channels (left and right usually, or could be front/rear), and outputs them into two different channels. Other types of amps you may run across is a one channel amp, which again amplifies one signal or channel.
Will 760 watt 2 channel amp power two 300 watt sub woofers?
Yes, but the amp is too powerful and if turned up to full volume will blow the speakers.
If you have two 900 watt RMS subs what size amp do you need to properly push them?
A 2 channel 900w per channel amp or less will run it, or a 1800w one channel amp etc.. Keep in mind the ohms need to match up too
How do you bridge three subs to a two channel amp?
3 passive sub at 8 ohm imp in parralel will be 2.6+ impedence.Most of the professional sum amp can take up to 2 ohms load per channel(check the spec of the Amp)eg: you should be able to connect max 4 subs in each channel(match the watts pwr to amp)
How do you hook up your dual voice coil 4ohm sub to one channel on two channel amp?
If you want max power flow connect the coils in parallel. Positive from 1 post to positive on the other post and same for negative. Then chose one post and run the positive to the positive of one channel on the amplifier and the negative to the negative of the other channel. That is called bridging.
Will a 100rms mini two way car subwhich doesn't need an amp to run work well with two 4 inch 3way 300w speakers and also two 6x9 400w speakers?
There MUST be some sort of amp powering the sub. An amp gives you power much like if you plug a light into a wall outlet. Hopefully there is a second 4-channel amp powering the speakers... Also, are you listing rms or max power for the 4" and 6x9" speakers? What sort of power is being run to the speakers also? Your question needs to be more specific to be able to answer it properly.
Is better to have a mono amp or 2 channel amp to 2 sub-woofers?
You won't notice any stereo separation with two subwoofers because our ears perceive bass as omnidirectional. Two subs can make more volume than one of the same size. If you are using two subs, you should either use two separate mono amps, or a two channel setup. As long as the amps have a high pass filter they will work equally well, although the wiring will be simpler for the two Chanel setup.
Can you run two eight inch subwoofers requiring 50-100 watts of power each running at 4 ohms with a 2 channel 4 ohm amp putting out 75 watts per channel without damaging the subwoofers or the amp?
Yes
