0
You probably could run your subwoofer off of the rear speaker outputs of your head unit, but you probably would not like the result.
It takes a great deal of energy to make bass tones and the power output of your radio is relatively limited.
The 'subwoofer volume' option is so that you can set the line-level output to a separate subwoofer amplifier and keep the subwoofer level proportionate to the main sound output.
Good luck.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Bridge two subs to a four channel amp?
If you amp is bridgeable you run + sub wire to ch 1 + then the -sub wire to the - of ch 2 of the amp. The same with the other sub + ch3 - ch4 that's how to bridge your amp.
Can you hook both a subwoofer and speakers to 1 amp If so do I need to buy a amp that's even more powerful Then what the sub requires?
You can connect a sub and speakers to one amp, depending on how many channels your amp has. A 4 channel amp will be able to run one (or two) subs using two channels (one bridged* sub or two subs) and two speakers running one channel each. A 2 channel amp will run 2 speakers or one bridged sub. A 6 channel amp will run one bridged sub (or two subs), 2 front speakers and 2 rear speakers. In my opinion, you will get the most performance, depending on which amps you use, by using a monoblock amp for your sub and an amp with enough channels to run all of your speakers. # Bridged = putting together the power of two channels to run one sub or speaker. Note: not all amps are bridgeable.
How can you install Sub woofers in a Buick without an AMP?
Cant you need a amp or you will blow the battery
Does it matter if you have a Jensen radio when trying to run a sub and amp?
No it does not matter.
Can you connect 2 amps to run a subwoofer?
If your sub is 2 ohms and your amp is 2 ohm stable, your done. Your amp will be at 2 ohms because the sub is 2 ohms.
Can you run 1800 watt 600 Rms Type R Sub with a 760 Watt Jenson amp If i Bridge the amp?
sure. Will it be loud? No. Its just not enough power to drive that sub.
You want to add a sub woofer to your stock radio without an amp?
To my knowledge that will not work. I don't think there is a stock OEM audio system capable of powering a sub. (Unless it came with a sub/amp from the factory)
How do you wire an amp and sub to a c240?
Run your power, ground, and remote wires. Then connect your RCAs to the back of your CD player and your amp, then connect your speakers to the amp..-Shocker
How do you wire a dual voice coil to an amp?
If you want to run both coils,you have to wire the positive to positive and negative to negative on your sub,then run a wire from each plug to the amp. Positive to the positive side of the amp and negative to negative side of the amp,(you can run in bridge mode or stereo if your amp can handle the load)
Correct way to hook up pioneer 12Ins sub woofer's champion series?
Depends if it is dual 4Ohm or dual 2Ohm and what Impedance your Amp supports. *If you amp can handle 1Ohm Load and you have a dual 2Ohm sub you can run the sub in parallel to get a 1Ohm load (parallel meaning both + are connected with each and same with both -) *If your amp can handle 2Ohm load and you have a dual 4Ohm sub you can run the sub in parallel to get a 2Ohm load. *If your amp supports a 4Ohm load and you have a dual 2Ohm sub you can run the sub in series to get a 4Ohm load. (series meaning the - from one coil is to be connected with the + on the other coil) Do not mix up Impedance's make sure you find out what your Subs Impedance is and what you Amps Impedance is
Can you use a 1000 RMS watt amp on your 500 RMS watt sub just to test if it puts out sound without blowing the sub?
You will most likely blow your sub
Can you feed a 60 amp sub panel from another 60 amp sub panel?
Yes
