0
Can you run your water heater and tanning bed off of the same breaker?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What gauge wire and amp breaker do you use on a stove dryer and hot water heater?
A stove is a two pole 50, and hot water heater i would recommend the same.
Does salt water help tanning?
Yes, salt water helps you tan. One day i didnt go in the water and i tried tanning, nothing really, next day (the same weather) i went into the water and tanned and i was darker.
Can you wire your water heater and dryer to the same breaker?
Under no circumstances should you do this.. for one they probably have different power requirements, but also they are high current devices, and by code MUST be put on separate branch circuits
Are vented and insulated the same thing on a water heater?
not even in the same state
How is heat transferred to water in a water heater?
In a gas water heater: The gas flame warms the water, exactly the same way as a gas stove burner does for a pan of water on the stove. In an electric water heater, an element - same as an electric range element, but a different shape - heats up from electrical current, and transfers that heat to the water.
What is a heater coil and a heater core?
The heater coil and a heater core is the same thing. Hot water circulates from the engine and through the heater core then back to engine generating heat for your heater system.
Can you connect an electrical shower into the same circuit as the tank immersion heater?
Would be best not to ... especially if both, when turned on, will exceed the amperage rating of the breaker to which they are connected.
Should a hot water heater be put on a 30 single or 30 double amp breaker?
What governs the type of breaker is the voltage and wattage of the heater elements. If the tank is 120V then you would only use one breaker. The size of the breaker you use will depend on the watts of the element. Watts = amps x volts, Amps = Watts/ volts. Once you establish the amperage then size the wire and the breaker to fit. If the tank is 240V the same rules apply only you would use a 2 pole breaker. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS. If you do this work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized.
How do you turn off a heater pilot light?
Same as any hot water heater. Turn the gas valve to off.
How to Figure out what is wrong with Your Water Heater?
A Tripped Breaker If you have an electric water heater and you are not getting any hot water at all, then the first thing that you need to do is make sure that the breaker has not tripped. This is a common problem and it is easy to fix. If the breaker had not tripped, then you can hit the reset button on your thermostat. This can be found in your access panel. Discolored Water If you have water that does not look clean, then you might have a build up of sediments in your water. This may also be the case if your water is taking too long to fill back up. You can solve this problem by draining your tank. After you have done this, you need to flush your tank out with clean water. Noisy Plumbing If your plumbing seems to be noisier than usual, you can check the temperature settings for your water heater. Noisy plumbing is usually a result of your water heater being too hot. The noise is just a build up of steam in your pipes. If it is too high, simply turn down the temperature. Sulfur Smell If the smell of your water seems slightly like sulfur, then you might have bacteria in your water. There are a lot of cases in which the build up of sulfur is too much for your water heater to handle. You can solve this by putting chlorine in your water. It is important to make sure that you do not put too much chlorine in your water heater. You can check your water heater owner’s manual for the right dosage. If you cannot find your owner’s manual, you can contact customer service for more help. Not Enough Hot Water Available If you do not have enough hot water for a shower or anything else, then you need to make sure that you are not using too many appliances at once. For example, your dishwasher and your washing machine are appliances that use hot water. If they both run at the same time, then your shower will be very cold and very short.
What is the electric code for water heaters?
In North America the code is the same for any connected load to a distribution system. The wire size and breaker are based on the wattage or amperage of the load. If the wattage is stated on the water heater use the following formula to find the amperage. I = W/E. Amps = Watts / Volts. Usually hot water tanks for homes are wired with a #12 wire rated for 20 amps and a 20 amp breaker to protect the #12 wire.
What is the difference between a combi boiler and a multi-point water heater?
A combination boiler provide hot water to a central heating system whereas the multi-point water heater does not. The multi-point water heater provides hot water to multiple appliances or taps at the same time.
