Yes and no. The voltage rating of the cord and appliance are compatible, so that's not an issue. However, the cord must be thick enough to handle the maximum load the appliance will draw (amperage). Thicker cords (lower wire gauge) can handle more current. Running high draw 120V appliances, such as toasters, microwaves, window AC units and especially hair dryers on extension cords or undersized wiring is a serious fire and shock risk. Special heavy duty appliance cords (usually 10 gauge wire and <10' long) are available for 120V applications at most hardware stores. Ideally, the cord would be hard wired into the appliance, and not be excessive in length. The ground pathway, if applicable, should be maintained as well.
Assuming "power cord" is an extension cord with a rating of 125V, 10A:
Yes. This means the extension cord is safely capable of carrying up to 125V and 10A. The 3.2A appliance is well below the limitations of the cord.
110V, 115V, 120V, 125V, 130V are all commonly used to reference the voltage found in homes (and businesses). The actual voltage output will vary from home to home, but typically falls 1 or 2 volts in either direction of 120V.
No problem what so ever. The 125 volt rating on the appliance is the maximum amount of voltage that is recommended for the appliance. This recommendation is set by the manufacturer of the appliance.
Yes, the 125 volts refers to the maximum amount of voltage that can be applied to the electric cord and still stay within the manufactures specifications.
Yes, the 125 volt rating is the maximum amount of voltage the manufacturer suggests to be applied to the appliance.
Yes.
Most 120 Volt appliances have their Watts listed somewhere on the appliance. Divide this number by 1,000 to get kilowatts. Determine the rate you are charged for electric power. Your electric bill will tell you how many kWh(kilowatt hours) you use, and what the total charge is. Divide your total charge ($?) by the kWh used. In northern Illinois, we are charged about $0.11 per kWh. Multiply the number of hours the appliance is used by its power consumption in kilowatts. This gives you the number of kWh the appliance used. Then multiply that kWh value by the rate for your area that you determined from your electric bill. That will be the cost for the number of hours the appliance was on. Example: If I toast 2 slices of bread in my toaster, it takes about 3 minutes, or 0.05 hours. My electric bill is $61.38 and I used 558 kwh for that month. Dividing $61.38 by 558, I get about $0.11 per kWh. So, I divide my toaster Wattage (750) by 1,000 to get 0.75 kW. So now I can multiply the hours that the appliance was used (0.05) by its power consumption rate in kW (0.75). This result is 0.0375 kWh of energy used. Then I can multiply the rate the electric company charges ($0.11) by the energy used (0.0375 kWh). The final result is $0.004125.
A delta connected appliance can be connected to a 3-phase system by leaving the neutral unconnected. The appliance must be properly earthed.
An extension cord holder is used to hold an extension cord. It wraps around the holder, for easy release and withdrawal.
To use an adapter of this sort, its rated voltage must match the rated voltage of the appliance, and its rated current must exceed that of the appliance. So, in your example, the rated voltage is too high to be used with your appliance.
There are two different electrical outlets for North America. The first, electrical outlet A, is used in North America and Japan. It is 2 blade NEMA 1-15 ungrounded. The second, only used in America, is 3 pinned NEMA and both are 15A/125V.
The cord can be used with Dell Alienware Laptop adapters.
No, it cannot.
No. If you plug something that needs 24 volt into a 120v socket you will probably ruin your device.
Electrical cord is also refered to as power cord, line cord, and main cable. Electrical cord is mainly used to connect the appliance to the main electricity supply via wall socket.
The voltage rating of a fuse (in this case 125V or 230V) defines the maximum circuit voltage that the fuse is safe to be used on. A fuse with a voltage rating of 125V should not be used in a circuit with a voltage greater than 125V. If a 125V fuse were installed in a 230V circuit and an overload current occurred, the fuse could explode.
Not unless the appliance is rated to be used with the two different power supplies. The US uses 120v, 60 Hz if it plugs into a receptacle, and possibly 240v, 60Hz if it is hard wired. The UK uses 240v, 50Hz whether it plugs in or is hard wired. These two power systems are NOT compatible. You may use a US appliance in the UK, and vice versa, only if the appliance is dual rated, i.e. the appliance says 120v/60Hz AND 240v/50Hz on the nameplate. If the appliance only specifies one power supply, it can only be used on that power supply. If this is the case, you may be able to use a travel adapter to operate the appliance.
Lamps use what is called a power cord. Power cords connect the appliance (in this case, a lamp) to a wall socket and the electrical field causes the filiment in the light bulb to beam.
No, it has to do with the insulation rating of the individual cords. 12 volts can be used on a voltage rating of 120 volts. But 120 volts can not be used on a 12 volt rated cord. As a point of interest most power cords have an insulation rating of 300 volts.
Well, a 120V appliance that draws 15A would be using 1800W. (15x120). A killowatt hour is one killowatt used continuously for an hour. If you used that device for one hour straight, it would use 1.8 kWh. (Keep in mind the device may not draw a full 15A)
All televisions are supplied with a power cord suitable for the model. If, for any reason, a new cord is used, it is important that you confirm it is correct for the television. The manual should provide the information but if there is any doubt, for safety, ask the advice of someone properly qualified before using a different power cable.
An appliance which does not use much current will perform satisfactorily with a long extension cord. Any device which uses a lot of power (space heater, large power tools) will not perform well on a long ext cord unless the cord is large enough and rated to carry the required power.
A power cord, line cord, or mains cable is a cable that temporarily connects an appliance to the mains electricity supply via a wall socket or extension cord. The terms are generally used for cables using a power plug to connect to a single-phase alternating current power source at the local line voltage"(generally 100 to 240 volts, depending on the location). The terms power cable, mains lead, flex or kettle lead are also used. A lamp cord is a light weight ungrounded two wire cord used for small loads such as a table or floor lamp. The term cord set is also used to distinguish those cords that include connectors molded to the cord at each end.