0
Can you use a 125v unnotched cable with a notched socket 120v ballast for your 1000 watt HID light fixture if you add a notch to the cord or remove the notch from the socket?
Wiki User
∙ 10y ago
See discussion page for more.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
If I remove two of the four lamps in my fluorescent fixture to save electricity should they be on the same ballast?
Yes
How do you test a ballast for fluorescent fixture?
Turn off the power, remove the bulbs, and remove the cover to expose the ballast. If you see tar leaking from the ballast it is bad and must be replaced. If you see no tar then proceed. Use a multimeter to check for continuity. The yellow and blue wires are the power wires and the white wire is neutral. With the meter set to ohms check between the yellow wire and white wire at the end where it connects to the light. If you get no reading the ballast is bad. Now check the other side where power is coming in. No reading and the ballast is bad. If you get a reading at both ends it is good. Check for loose wires.
How do you repair a fluorescent light located under a kitchen cabinet?
Unless there is something special about this fixture, it will be cheaper to replace the entire fixture. However if you choose to repair it, the ballast is the most likely reason for its failure. Turn off the power,remove tubes and then the cover from the fixture.You will see a small rectangular object with wires going into it.This is the ballast,usually it is apparent that the ballast has failed.Get the part # from the ballast and pick one up at your local supply house.Replace the ballast and reconnect the wires per old ballast.Also inspect the ends where the tubes connect, sometimes these get burned and do not make good contact.Hope this helps. above answer correct but i would simply replace the tube or tubes first. i have a lot of experience with about 30 of them in my laundromat.
How do you remove the dome from a light fixture?
Take the nut off at the bottom of the light fixture by unscrewing it.
How do you remove condensation from inside headlights?
You can remove the entire headlight fixture by removing 2 clamps on the back side. Pull entire fixture forward, turn over and drill 2 or 3 small holes on the bottom side of the fixture toward the rear of the fixture.............
How do you release dome from light fixture in ceiling fan?
Disconnect the fixture wires and remove the central mounting nut to release the dome from the light fixture in a ceiling fan.
How do you replace the fog lights for a 2003 Chevy Tahoe?
Remove the socket from the rear of the fixture, remove faulty bulb from socket and replace with good bulb and replace socket in fixture. Fini!
How do you remove the tail light lens from a 1989 Chevy Celebrity?
The tail light lens on a 1989 Chevy Celebrity is part of the tail light fixture and cannot be conveniently removed. If you want to change a light bulb you have to remove the tail light fixture from the car. To remove the tail light fixture: 1. In the trunk next to the quarter panel are three nuts, remove the center nut. It should be in the center of the tail light fixture. 2. Pull the tail light fixture so that the stud comes out of the body, then pull outward to pull the tab out of the backup light fixture. 3. You can now take the appropriate socket out and replace the bulb. Reverse the steps to replace the light fixture.
How do you replace the ballast on a 2003 Acura CL 3.2?
First, disconnect the battery as a safety precaution. One of these HID ballasts can cause electric shock or electrocution. Second, remove the front bumper cover. Then remove the headlight assembly for the ballast which needs replacement. The ballast can be found on the bottom of the headlight assembly. Replace the ballast and reinstall all removed parts. Reconnect the battery and confirm the repair.
How do you replace the 3rd brake light on 2006 Malibu?
First, remove the inside trunk lid cover panel. Disconnect the electrical connection. Use a spin tight wrench (7mm) to remove the two screws. Unclip and remove the protective cover. Unclip and remove the light fixture. The light fixture is LED so you will need to replace the entire fixture, it's about $60 at the dealership. I just did this procedure last night.
How do you remove the rear panel in a 1989 Chevy Celebrity to replace a tail light?
To remove the tail light fixture on a 1987 to 1990 Chevy Celebrity sedan: 1. Inside the trunk next to the quarter panel are 3 nuts. Remove the center nut, it should line up with the center of the tail light fixture. 2. Pull back on the tail light fixture until the stud clears the body. 3. Pull outward on the tail light fixture to remove a tab from the back up light panel. 4. Twist the appropriate socket counter clockwise and remove it. You can now replace the light bulb. Reverse the process to put the tail light fixture back in place.
Who to remove glued-on bathroom light fixture from mirror?
To remove a glued on bathroom light fixture from a mirror, the best product to use is WD-40. Spray on the WD-40 and wait a few minutes while holding up the light fixture so it will not suddenly fall. Gently pull on the light fixture while using a putty knife to scrape the area underneath the lamp next to the mirror. Glue residue can also be cleaned up with the WD-40 after the fixture releases.
