0
Yes, the maximum that the adapter can deliver is 1300 mA or 1.3 amps. The maximum that the device will draw is 200 mA or .2 of an amp.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Can you use a 9v 300mA adapter on a 9v 200mA device?
No. The adaptor will overheat.
Can you use a adapter 15VDC 1A to replace adpater 15VDC 200mA. will it fry my device?
No it will not harm the plug in device. The 1 amp relates to 1000 mA or in other words it has five time the capacity as the 200 mA adapter.
Can a 100 mA adapter be substituted with a 200 mA adapter?
A 9V 1A adapter will supply up to 9 Watts of power and a 9V 200mA adapter delivers up to 1.8W of power. The 200mA adaptor may not be able to supply enough power to a device that has been supplied with a 1A adapter. The 1A adaptor should operate equipment that originally used a 200mA adapter. Before using a different power supply, check that the outputs are both DC or both AC. If they are both DC, it is important to check that the polarity at the connector is the same for both. If AC and DC supplies are swapped or the polarity is swapped there is a risk that the equipment will be damaged.
Can a 9v 800ma adapter be used on a 9v 200ma device?
Yes. There's a subtle difference in the meaning of the "--- ma" labels on the two units:-- On the "device" ... the unit that uses power ... the "200ma" is the current it useswhile it's operating.-- On the "adapter" ... the unit that supplies power ... the "800ma" is the maximumcurrent that it's able to supply. Anything less than that is easy.So your adapter is OK to operate your device. In fact, with suitable wiring and a bit ofcooling, it could nominally operate 4 of them at the same time.
Can you use a dc 9V 400mA ac adapter in place of 9V 500mA adapter?
No. The 200mA adapter will only produce 1/8th the current of the 1600mA adapter, and probably won't even power what you intend to use. If it does, the extreme undercurrent will likely damage the equipment itself. A possible solution is a universal adapter, which may allow you to set the voltage and/or current for use with the intended device.
What is the voltage of a uniden bearcat sportcat sc 150 charger adapter?
INPUT: AC 120V 60Hz OUTPUT: DC 12V 200mA
Can you use a 9v dc 200mA ac adaptor in place of a 500mA?
Yes. The current rating should be the same or greater than the original. This means the adapter can supply up to 500mA; In your case it only needs to supply 200mA, so it is more than up to the job.
200ma in amps?
200ma is .200 amps or .2 amps
Can a 12v dc 500mA adapter be substituted for a 12v dc 200mA ac adapter?
No.If it is AC output, it will blow out the power circuits of the DC device.If it is DC output, it doesn't have enough current capacity for the load of the DC device.If you want to power a DC device with a wall wart, make sure the wart is:DC outputCorrect polarity (some have reversible polarity)Exact same voltage as the deviceGreater than or equal to current rating of the device
Can a 9 volt 1000 m a adapter replace a 9 volt 200 m a adapter- the polarity is the same-this is not bein used as a charger its being used to power a guitar effect pedal in place of 9volt battery?
Some 9 V adapters rated for 1000 mA will provide 9 V at 1000 mA. If you use it on a 200mA device the voltage may go up to 10-15 V and if that device can not handle the higher voltage, it it could burn out. Better adapters will only put out 9 V exactly and have no problem. Be careful of revere polarity where the positive on one is the negative pin for the other adapter.
Can you use a DC 9v 300MA adaptor to power a 9v 400MA device?
The voltage would match but the amount of power would likely not be enough to run the device. Under-power will not likely harm the device, but it won't work correctly. Always use the correct voltage/power for your devices!
Can you use 12v 500mA adapter to tv antenna that has 12v 200mA?
YES!If you have a TV antenna amplifier rated at 12 Volts and 200 milliamps, you can use any power supply that will deliver at least 200 milliamps at 12 Volts. The important item is to keep the 12 volts at 12 volts. note: 200 milliamps is 0.2 amps. Even if you had a power supply that delivered 2000 amps at 12 volts you would be OK as it will only draw the 200ma that it needs.
