In general, yes. There are three things you need to concern yourself with when using electric or electronic devices in other countries: # The voltage
Most, but not all devices have a tolerance that will accept a range between 220 and 240 volts. Many modern electronic devices accept a voltage range from 110 Volts to 240 Volts.
# The frequency
Some devices - especially anything with a motor built into it - will only work properly if supplied with an alternating electric current of the specified frequency. In North America, the frequency is 60 Hz, in Europe it is 50 Hz, and it varies elsewhere. Even if you have the correct voltage, plugging a motor into a supply with the incorrect frequency can damage the motor.
# The plug form factor
Plugs differ from country to country, even when those countries use the same voltage and frequency. Without the correct plug adapter, you may not be able to plug your device into another country's power receptacle.
No you can't do that, you can only damage the equipment due to voltage overload. It is much better to use a voltage that corresponds to your equipment or use a transformer.
<><><>
It is not clear what this question is asking. Here are four possible meanings:
* Can a 120 volt appliance run from a 240 volt socket outlet?
* How can you change the plug on a 120 volt appliance to plug it into a 240 volt socket outlet?
* Can you convert a 120 volt socket outlet into a 240 volt socket outlet?
* Can you convert a 240 volt socket outlet into a 120 volt socket outlet?
For more information - which may or may not be relevant depending on what this question is actually asking - please see the answers to the Related Questions shown below.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Yes, but the lamp will not last as long. HOWEVER, if the lamp is designed for European voltage, where one hot wire carries the voltage, it will NOT work on a lamp that is desinged for two hot wires.
There should be no problem at all.
Yes and you will have a spare terminal for future use
220 volt will use less energy.
The coil can be operated by taking one leg of the 240 volts from the top of the contactor and connecting it to one terminal of the coil. Take the other leg of the 240 volts from the top of the contactor and connect it to the device used to turn the contactor off and on. From this switching device take the switched wire and connect it to the other terminal on the contactor's coil. Now when the switching device is activated the contactor will open and close.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
AC voltage conversions are usually done with transformers. Most commonly, a 3 phase 277/480v system is transformed to a 3 phase 120/208v system. You can, however transform to anything you like with the proper transformer. If you are trying to convert 480v single phase to 240v single phase, such as for home use, then ask for that type transformer. It would use only 2 phases of the 3 phase system. Using 2 phases is called single phase and there are reasons for this that are beyond the scope of this answer. 220v and 110v are field measurements of what is considered 240v and 120v when ordering equipment or applying code.
There should be no problem at all.
Most appliciances that are built for use with 220V would normally be fine with 240V. In most cases, they are also labeled 220-240V. Depending on how critical the application is, you should probably check with the manufacturer.
If all the components are rated to 220V, yes. Keep in mind that if the appliance was designed for 110V it may arc if 220 is run through it. If you don't know the device can handle 220V, don't run it at 220V. Chances are it was manufactured cleaply and cannot handle the extra voltage.
I guess it will, but it depends on the type of device you use. An electric bulb may glow with reduced intensity at the same time, a regulated psu based device may balance the voltage by drawing required amount of current to bring it to 240V inside the psu unit of that device. It again depends upon the device. Some devices use some range of input operating voltages like 220V ~ 240V.I guess I'm right
Yes. Spain voltage is 220v, English is 240v (which is close enough!) Spain television uses PAL, as does English.
In some parts of the world, an 1875 watt hair dryer can and does use 220 volts from a 220 volt outlet?
minimum 230volts In formal electrical jargon, a "device" does not "use" electricity. A device is something like a switch or receptacle(outlet) that helps control or carry electricity but does not consume electricity. In the United States, voltage for home lighting and general purpose receptacles is 120v. Voltage for electrical appliances such as ranges, clothes dryers, or furnaces is 240v. Voltages such as 110v, 115v, or 125v are versions of 120v in electrical jargon and voltages such as 220v or 230v are versions of 240v.
You cannot directly plug a 110v device into a 220v outlet. This can cause damage to the device or even create a safety hazard. You would need a voltage converter or transformer to safely convert the 220v outlet to the appropriate voltage for the 110v device.
No. You can't replace a 220V outlet with a 110/220V outlet without running the requisite neutral wire. If you do you will blow out any device that expects the neutral line to be connected.
If it is AC, a transformer. If it is DC, a motor generator.
Yes, you can use a 230 volt device on a 240 volt supply.
Is the 220V plug 220V only or 110/220V? (The former will have 3 prongs and the former will have 4) If your case is the latter just use the ground, neutral, and one of the hots. This will give you 120V single phase. If the case is the former you can't get 110V off that plug.