0
Can you use a hydraulic valve lifter treatment for a slight tapping noise?
Wiki User
∙ 10y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
After 60 hrs on your new 350 vortec boat engine a lifter appears to be making a slight tapping sound you suspect it is because the boat sits in the sun without use Any ideas?
No, not the sun. The lifter needs to be ajusted. Also check the oil make sure its not low.
What are cons of rubber tapping?
Rubber tapping causes slight harm to the tree they're tapping from, by leaving scars on the bark of the tree from where the rubber was tapped from.
Whats wronng with your car you hear a slight tapping sound coming from your engine in your 1996 Chevy luminu?
chances are good in your 1996 Chevy lumina if there is a slight tapping noise, check the oil. it may be low, or you may need to add a thicker additive. good luck!
What disease causes compulsive blinking?
It's a more common than you think "OCD." It's not a disease, it's a disorder. It's commonly found along with slight / very slight twitching of the head and frequent tapping of the fingers.
What are the risks of getting a thermage skin treatment?
Slight reddness, swelling, bumps, or small heat blisters immediately following treatment. Depression in the skin. Painful and it may not work. Slight irritation, like a mild burning sensation. The treatment may not work so you may have to pay for another one.
Does Viviana have brown hair?
She recently had a henna treatment, which she says gives her hair a slight burgundy tint.
What exactly is the meaning of singe?
A singe is a slight scorch, burn or treatment by a flame. In the textile industry, loose threads are singed to remove them. At barber shops, singeing can be used as a treatment.
Do you need new hydraulic roller lifters if you have a new cam?
Officially you should change lifters anytime you change the cam. In real world use; unless the roller lifters have obvious, visual damage, missing pins, wear on surface of the roller, then it is not normally going to be a problem. In the case of flat lifters, you should change them. The cam of flat tappet (regular) lifters, have a slight bevel to the surface of the cam. When the cam and lifter are in operation - this causes the lifters to rotate in their bore. After/during break-in, there is some wear on both surfaces and they end up with a pattern which is unique for each bore and and each cam/lifter combination. If you change either the order of the lifters on the original cam they meshed with, or install a new cam or new lifters - there is a very real chance of accelerated wear leading to failure of cam and lifter. What is worse - the resulting debris can follow the oil and ruin bearing surfaces throughout the engine. Your money, your choice.
How do you unlock a thermostat?
There is a slight possibility that light tapping on the housing may break it free, but too hard of a hit will break the housing. If the thermostat does free up it is most likely going to stick again. The best bet is to replace the thermostat.
What can cosmetic laser treatment be used for?
Cosmetic laser treatment can be used to smoothen wrinkles on the face and body, and can also be used to remove pigmentation, such as birth marks or slight scarring. It can also be used to remove warts and some tattoos.
What cylinder is better hydraulic or pneumatic?
Strictly speaking, which is better depends on the equipment of which this cylinder is a part of. Pneumatic systems take on slight change in volumes (as air can get compressed on load and reduce in volume) and hence, a big NO for systems where even minute linear movements are critical. Hydraulic systems offer exact displacements. There are other considerations too
Why does a 1997 ford explorer make a clicking noise when opening the oil cap?
If you have a 4.0 SOHC engine you are hearing the timing chain rattle against the timing chain guides. Some slight noise is normal, but an excessive amount may mean you have timing chain guide and/or tensioner problems. If you have a 4.0 OHV engine, then you are probably hearing some lifter noise. Again, some may be normal, but excessive may be an indication of lifter troubles.
