0
Can you use a potentiometer to adjust the voltage on a dc motor that works between 9 - 18 V?
Wiki User
∙ 14y ago
Probably not, at least not directly...
Potentiometers can be used to vary the voltage in a circuit, but they typically do not have a large power rating. Most DC motors, even small ones, pull enough power to overheat a potentiometer.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you control rpm of single phase motor without using variable frequency drive?
By changing the voltage through a potentiometer ( eg fan regulator )
What type of speed control system uses a wire -wound potentiometer?
A potentiometer is another name for a variable resister used for voltage dividing. Potentiometers have three tabs on them The two outer most tabs have the full resistance of the device across them. The center tab is connected to the wiper that slides across the surface of the resister. A voltage is applied to the two outside tabs on the potentiometer. A voltage of your choosing will appear across either the left tab to the center wiper tab or from the right tab and the center wiper tab. A potentiometer of this type is used to control the speed output of variable frequency drives. A 10K potentiometer has 10VDC applied across the two outside tabs If the drive sees the full 10 volts it allows the drive to go to full output and the motor will run at full speed. With the potentiometer's center tab wiper at half position a voltage of 5 VDC will appear to the drive. When the drive sees the 5 volts it tells the drive to go to half speed output and the motor will run at half speed. This potentiometer is linear so no matter where the wiper is positioned, the motor speed will follow the potentiometer settings from 1% right up to 100%
A potentiometer is used for?
A potentiometer is a type of position sensor. They are used to measure displacement in any direction. Linear potentiometers linearly measure displacement and rotary potentiometers measure rotational displacement. Also known as a Potmeter or Pot, it consists of a resistive element called the track and a sliding contact called the wiper internally where end terminals are attached to the resistive element. They are used to accurately measure voltage and help achieve a variable voltage from a fixed-voltage source. Common Examples of Potentiometers are: Measuring Position on a gaming joystick Controlling audio equipment using volume controls
What is the different between 3phase plus N generator coil and motor coil?
Generator coils generate the voltage, motor coils use the generated voltage.
What is the purpose of a potentiometer?
A potentiometer is a type of position sensor. They are used to measure displacement in any direction. Linear potentiometers linearly measure displacement and rotary potentiometers measure rotational displacement. Also known as a Potmeter or Pot, it consists of a resistive element called the track and a sliding contact called the wiper internally where end terminals are attached to the resistive element. They are used to accurately measure voltage and help achieve a variable voltage from a fixed-voltage source. Common Examples of Potentiometers are: Measuring Position on a gaming joystick Controlling audio equipment using volume controls
Working principle of servo motor?
Servo motors are geared DC motors with the closed-loop circuitry incorporated within them. The basic configuration of a servo motor composed of a DC motor, gearbox, potentiometer and control circuit.DC motor is used to move a gearbox with a large reduction ratio. The final shaft imposes a force on the external load and simultaneously acts on the axis of the feedback potentiometer. So, the potentiometer senses the position of the axis and sends a corresponding voltage to an operational amplifier. This voltage compared to the input voltage, that determines the desired position of the shaft, producing a voltage in the output of the comparator. This voltage powers the motor such that the shaft moves in the necessary direction to align with the angle that corresponds to the voltage applied to the input.
How the servo potentiometer works?
A potentiometer is another name for a variable resister used for voltage dividing. Potentiometers have three tabs on them The two outer most tabs have the full resistance of the device across them. The center tab is connected to the wiper that slides across the surface of the resister. A voltage is applied to the two outside tabs on the potentiometer. A voltage of your choosing will appear across either the left tab to the center wiper tab or from the right tab and the center wiper tab. A potentiometer of this type is used to control the speed output of variable frequency drives. A 10K potentiometer has 10VDC applied across the two outside tabs If the drive sees the full 10 volts it allows the drive to go to full output and the motor will run at full speed. With the potentiometer's center tab wiper at half position a voltage of 5 VDC will appear to the drive. When the drive sees the 5 volts it tells the drive to go to half speed output and the motor will run at half speed. This potentiometer is linear so no matter where the wiper is positioned, the motor speed will follow the potentiometer settings from 1% right up to 100%
How do you you control the speed of a dc motor?
A Potentiometer, an adjustable resistor, is connected between the power source and the motor. An AC motor would use a Rheostat .
How do you control rpm of single phase motor without using variable frequency drive?
By changing the voltage through a potentiometer ( eg fan regulator )
What is the principle of potentiometer?
A potentiometer is another name for a variable resister used for voltage dividing. Potentiometers have three tabs on them The two outer most tabs have the full resistance of the device across them. The center tab is connected to the wiper that slides across the surface of the resister. A voltage is applied to the two outside tabs on the potentiometer. A voltage of your choosing will appear across either the left tab to the center wiper tab or from the right tab and the center wiper tab. A potentiometer of this type is used to control the speed output of variable frequency drives. A 10K potentiometer has 10VDC applied across the two outside tabs If the drive sees the full 10 volts it allows the drive to go to full output and the motor will run at full speed. With the potentiometer's center tab wiper at half position a voltage of 5 VDC will appear to the drive. When the drive sees the 5 volts it tells the drive to go to half speed output and the motor will run at half speed. This potentiometer is linear so no matter where the wiper is positioned, the motor speed will follow the potentiometer settings from 1% right up to 100%
What type of speed control system uses a wire -wound potentiometer?
A potentiometer is another name for a variable resister used for voltage dividing. Potentiometers have three tabs on them The two outer most tabs have the full resistance of the device across them. The center tab is connected to the wiper that slides across the surface of the resister. A voltage is applied to the two outside tabs on the potentiometer. A voltage of your choosing will appear across either the left tab to the center wiper tab or from the right tab and the center wiper tab. A potentiometer of this type is used to control the speed output of variable frequency drives. A 10K potentiometer has 10VDC applied across the two outside tabs If the drive sees the full 10 volts it allows the drive to go to full output and the motor will run at full speed. With the potentiometer's center tab wiper at half position a voltage of 5 VDC will appear to the drive. When the drive sees the 5 volts it tells the drive to go to half speed output and the motor will run at half speed. This potentiometer is linear so no matter where the wiper is positioned, the motor speed will follow the potentiometer settings from 1% right up to 100%
A potentiometer is used for?
A potentiometer is a type of position sensor. They are used to measure displacement in any direction. Linear potentiometers linearly measure displacement and rotary potentiometers measure rotational displacement. Also known as a Potmeter or Pot, it consists of a resistive element called the track and a sliding contact called the wiper internally where end terminals are attached to the resistive element. They are used to accurately measure voltage and help achieve a variable voltage from a fixed-voltage source. Common Examples of Potentiometers are: Measuring Position on a gaming joystick Controlling audio equipment using volume controls
What is the different between 3phase plus N generator coil and motor coil?
Generator coils generate the voltage, motor coils use the generated voltage.
Does the servo motor contain the servo?
A "servo motor" and a "servo" are the same thing. Servos are constructed from three basic pieces; a motor, a potentiometer (variable resister) that is connected to the output shaft, and a control board. The potentiometer allows the control circuitry to monitor the current angle of the servo motor. The motor, through a series of gears, turns the output shaft and the potentiometer simultaneously. The potentiometer is fed into the servo control circuit and when the control circuit detects that the position is correct, it stops the motor. If the control circuit detects that the angle is not correct, it will turn the motor the correct direction until the angle is correct. Normally a servo is used to control an angular motion of between 0 and 180 degrees. It is not mechanically capable (unless modified) of turning any farther due to the mechanical stop build on to the main output gear.
What is the phase voltage inside a motor if one phase is lost and what is the voltage between the other two phases?
The phase voltage is usually constant and determined by the supply voltage.
Speed control of three phase induction motor by supply voltage control using AC voltage regulators?
No. Use standard utility AC, 3 PH voltage to feed a Variable Frequency Drive (VFD). The VFD is then wired to the motor. The output of the VFD varies average voltage and frequency in a semi-constant proportion to keep Volts/Hertz ratio the same to the motor. The operator can then adjust or select the desired speed from the VFD and the VFD will run the motor continuosly at that desired speed. If you were to control only voltage to the motor without adjusting frequency in proportion, the motor would burn up.
What is the difference between a motor starter and a contactor?
Motor started will have overloads the contactor connect es line voltage.
