0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What size condenser do you need to match a 5ton 10 seer coil that is at least 9 years old?
A 5 ton 10 SEER condenser will do it, but you can no longer buy a 10 SEER condenser. Replacing the condenser and not matching it with the proper evaporator coil will nullify the SEER value stated on the new unit and your actual SEER and EER will be anyone`s guess so do not pay any attention to it. The coil is the least expensive component of the 3 and now would be the time to upgrade away from R 22 which is currently being phased out and will become very expensive in the near future. Something to consider if that 9 year old coil were to fail before the new condenser does or if you were to develop a troublesome leak. But if you are dead set against the coil replacement I suppose a 4.5 or 5 ton, depending on the climate where you live will work. Get the lowest SEER currently available (13) since it will mean nothing.
Replacing coil on 318 Chrysler old coil has external resister new coil has built in what do i have to do?
Purchase the right coil for that vehicle.
How do you replace the ignition coil on a 94 Dodge Intrepid?
Disconnect the battery.Remove the air filter tubing.Remove the plug on the old coil.Switch the plug wires from the old coil to the new coil.Remove the four bolts from the old coil.Bolt the new coil into place.An instructional video has been included below.
How do you put on a ignition coil 1974 vw beetle?
The coil fits in the coil bracket, which is normally on the fan shroud. Take the old coil off the car and set it down with the wiring pointed up. You will see two bolts coming out of the coil, one with a + and one with a -. The + bolt should have a metal piece with a place to hook three push-on connectors; the - bolt should have a metal piece you can hook two push-on connectors to. So the drill is, move all the wiring that's on the + side from the old coil to the new one, move all the wiring from the - side of the old coil to the - side of the new one, move the center wire from old coil to new, put the coil bracket on the new coil, bolt the coil onto the fan shroud and you're done. It'll take ten minutes at most.
How do you install Coil Boots On 1999 Lincoln Cont?
Pull old ones off coil and stick new ones on.
What is the approximate cost of a furnace and ac for a 1000 sq ft house?
Cost may vary depends on the house size, accessibility, the amount of work involved in duct reworking, disconnecting/connecting gas electricity. Normally, it's better to replace AC/coil/Furnace all together, since a new furnace may not be compatible with old indoor blower /evaporator coil.
How do you replace ignition coil for 1984 Chevy Celebrity?
To replace the ignition coil: Unplug the wires from the coil, take note of how they come out so you can put them back. Unbolt the bracket from the intake manifold. The original coil is riveted to the mounting bracket, the new coil usually comes without the mounting bracket. Next cut the rivets off that hold the old coil to the mounting bracket. The new coil normally comes with bolts to hold it to the old bracket. Install the new coil to the mounting bracket then mount the bracket to the intake manifold. Plug the wires back in.
How do you replace coil springs 2002 impala?
take the old ones out and put new ones in
How do replace the ignition coil of an Hyundai Elantra?
take the old one out and put the new one in.
Why condenser used in tube light?
A tube light uses a condenser which is the old term for a capacitor. It functions as a small battery in a circuit.
How to Convert hvac r22 to hvac 410r?
Step one removalyou have to recover all freon from system then cut out the condenser unit and the evaporator coils and remove freon lines in between.Step two replacingonce the above is done you will install the new freon lines via Brazing (size depends on the new condenser unit) you will need to retro fit the new evaporator coils to the old furnace (unless you have replaced that too) and install the new condenser unit.step three checking for leaksplace vacuum pump on a line and pull a vacuum for 24-48 hours and close your gauges and turn of the pump check the vacuum make not of where it is (it should not be at 0) wait 24 hours and then check it again it should be the same (IE if it was 28 merc. then it should be 28 merc. after 24 hrs)if not use nitrogen to locate leak.step four chargingALWAYS CHARGE IN LIQUID STATEcharge via super heat or use scales to get close to proper charge and then finish via super heatstep five finalizingreconnect electricity, insulate liquid line(s), turn on and enjoy
How can you tell a coil pack is bad on a 1995 Pontiac grand prix se 3100 motor?
go get a new coil pack just 1! take one of the wires on the old pack off & wire up a new one start engine up if u see arcing then that old pack still works proceed down the line until one of the old packs does not arc then u have found your bad coil pack! take off and replace with new coil pack and you should have a smooth firing order and idle
