Phantom power won't hurt your dynamic mic, but it also won't help it. Turn off phantom power if you're using a dynamic mic. Only condenser microphones need phantom power.
These devices contribute to the energy-wasting phenomenon called "phantom power," or vampire energy. Simply put, this is the power that is used when electronic devices draw energy from the grid into your home just by being plugged in, when you aren't looking and you aren't using them. Many electronic devices continue to draw power even when not in use. Energy drawn by the standby mode sometimes is referred to as a "phantom load." An estimated 50 percent of the energy used by an electronic device is drawn while the device is not in use, making phantom loads responsible for 4 to 7 percent of your total electricity use. Phantom loads can be reduced in many ways, some of them for little cost or free.
People often feel phantom limb pain after having a limb amputated.Many people enjoyed watching Phantom of the Opera.
Static storage allocation is when a program dedicates an amount of memory for its use at the start of the program. Dynamic storage allocation is when a program only takes storage as it needs it.
Dynamic simulation is the use of a computer program to model the time varying behavior of a system. In contrast, steady state simulations cannot model variations in variables over time.
They use electrical power.
usually a dynamic microphone is used for live performances such as a rock band because its not as sensitive as a condenser mic which is used for recording.
"Phantom Power" in use in the recording industry is ALWAYS 48V. Some types of mics use other types of power like T-power or an internal battery, but this is not "Phantom Power".
nope need some source of phantom power...try a preamp
In Pro Tools 9 or 10, you can use the MobilePre as an audio interface. You must select it as the input in the hardware options. The mic must be connected to one of the XLR microphone inputs on the MobilePre, the phantom power turned on if it is a condenser mic, and an audio track armed with the first or second input selected (depending upon where you plugged in the mic).
Using a sound input that is built into a computer isn't the best solution: An external sound card will normally produce better results but whether you use a built in sound card or an external one, there are two or three ways to connect a microphone. A dynamic mic can connect directly to the 3.5mm microphone input jack. Most of the lower cost mics are dynamic although there are many studio mics available. A condenser mic can be used but they normally need a voltage on the input connector to power them. Condenser mics are normally the preferred choice for recording and they can be used if a "phantom power supply" is connected between the mic and the input. With any microphone, an adaptor may be needed from either a 1/4" jack or an XLR connector to the 3.5mm socket. Many electronics stores will have the right adaptors. An alternative is to use an external mixer. One or more microphones can be connected to it and the output will be at a higher level than a single microphone and is likely to offer a better quality sound capture than using a microphone level into the sound card.
Unless you already have a soundcard with phantom power, then one relatively inexpensive solution is the Tascam US-122 USB Audio/MIDI interface. That's what I use to power my condenser mic and the sound is very clean and crisp. Good luck!
This depends entirely on your budget. Condenser mic can capture wide range of frequencies and thus it is recommendable.
it doesnt have mic ...
you cant do it
yes you need to have a controller to be able to use the mic. (you can use the mic on guitar hero 4 and upwards)
A preamp is required for all microphones, and is built in to the mixer if it accepts microphone inputs. The feature required for most condenser microphones is phantom power, a 48 volt signal that is supplied by the mixer to power the electronics inside the microphone. You must use an XLR (three pin) cable to connect the mic to the mixer to provide this power. There will be a Phantom or 48V switch on the mixer to turn this feature on and off.
Microphones are not TDM, RTAS or VST. Those are categories applied to different types of plugins. Mics can be condenser (aka capacitor), electret, dynamic, ribbon, etc. Some require 48 volts phantom power to power them (condenser mics). Plugins used for your audio software can be categorized by being TDM, RTAS, VST or DirectX. TDM and RTAS plugins are usually used for Pro Tools. VST are used by Steinberg Cubase. Some other applications can use VSTs and maybe some can use TDM and RTAS. There is another kind too: DirectX plugins.