Can you use the exhaust manifold from a 1990 gsi on a base model 1990 geo storm?

it is in the exhaust manifold,or exhaust pipe...

it is located on the drivers side of the engine under the air intake manifold

The oxygen sensor is located on the exhaust manifold and is the only item on the exhaust with wires going to it.

18 to 22 lbs

It is located in the exhaust manifold.

on the back of the block by the exhaust manifold

The oxygen sensor is usually mounted in the exhaust manifold pretty close to where the exhaust pipe bolts on.

on the rear exhaust manifold, directly behind the motor

It is screwed into the exhaust manifold on the back of the engine.

on the drivers side just under the exhaust manifold

If you aren't hearing a lot of exhaust noise and you're just getting smoke, you have either an oil leak or antifreeze leak that is getting on the exhaust manifold. If you're getting oil on the manifold you have a fire hazard and should take care of the problem immediately. If you hear exhaust gas leaking around the manifold you need to replace the gasket or possibly the manifold is cracked and you need to…

screwed into your exhaust manifold.

in the exhaust manifold. is there any place to buy a used one?

It is installed on the top of the back side exhaust manifold.

It is mounted in the exhaust system. Start at the exhaust manifold and work backward toward the catalytic converter. It is more than likely mounted in the exhaust manifold right at the engine. It may also be mounted where the two exhaust pipes come together.

On the 5.7 350 just one in the exhaust manifold on drivers side.

you jack the car up, whatever side exhaust manifold u take off that side of tire u remove the heat shield and unbolt that manifold. u take off that tire because u have to get those hard to reach areas , and you might need to take off the exhaust from under the car it takes about 20 min if u know what your doing, but its pretty simple

The flex pipe is a pipe that conects the exhaust manifold to you exhaust so that when the moter shifts it doesn't shake the whole exhaust syster. Yes it can be the reason that you car is so loud. Answer OR, it is a cheap way to replace a faulty exhaust pipe. Hi, I own a 1990 Plymouth laser also. The flex pipe is on what they call the "J" pipe. It attaches your exaust…

Dont laugh when i ask this but I seen it happen before, Is there gas in the tank?

Six cylinder, on the front behind the engine mount. Four cylinder, rear of the engine under the exhaust manifold.

its in front of car in the exhaust manifold, u need a special socket to remove oxegyn sensor. fairly easy

This year only has one. It will be either in the driver side exhaust manifold or in the pipe directly behind the engine.

Locate it at either the exhaust manifold or the ex pipe and unplug it and unscrew it. Use anti seize compound when replacing it.

CHECK FOR PLUGGED CATALYTIC CONVERTER, MOST OF THESE ARE IN THE LOWER SECTION OF EXHAUST MANIFOLD, IF ITS IN THE PIPE, LOOSEN THE HEAD PIPE ALLOWING THE EXHAUST TO BREATH, RAN INTO MANY OF THESE. GOOD LUCK, BRIAN

My Chilton book shows 2. One right after the exhaust manifold then another a little farther back before the muffler.

Head bolts ------------------------------ 65 lb/ft Intake Manifold (Cast iron heads) -- 30 lb/ft Exhaust Manifold ----------------------- 25 lb/ft Valve Cover ------------------------------ 3 lb/ft

If it's in the way, then yes. Don't dis-connect the lines, though. Tie the compressor up out of the way.

what motor is it? on my 1990 F150 5.8L 351W its located on the front passenger exhaust manifold. looks kinda like a space ship

If it has a 3.1L engine, it'll be in the exhaust pipe just after the exhaust manifold. Rotate the engine forward, look down between the engine and firewall, it'll be pointing up at you, with a wire coming out the top. Cheap/easy to replace, will better your mpg's!

On a 1987 to 1990 Celebrity with 2.8/3.1L engine the crankshaft position sensor is on the side of the block beneath the exhaust manifold on the firewall side of the engine.

the sensor for the gauge should be by the thermostat housing,the sensor for the ecm should be on the right rear of engine above exhaust manifold screwed into head

If you mean o2 sensors, there is one. It is located on the exhaust manifold on the back side of the engine. Gm started the two o2 sensors around 94-95 when obdII was adopted.

I have a 1990 Pontiac sunbird and i was only able to find one, it was behind the exhaust manifold on the block. I myself am having problems finding the other. I hope this helps.

being a 1990 it may have a distributorles ign, find one of the spark plugs,and follow one of the wires back to the end. if it goes to a small black box, then it is a distributorles. There is no distributor. It has coil packs located underneath the front exhaust manifold.

Storm and Sorrow - 1990 TV was released on: USA: 22 November 1990

There is air in my manifold and can't find the bleeder valve to release it so how do i bleed my manifold?

Open the hood and look straight down between engine and cooling fan. You will see the exhaust manifold. It should be under that bolted to the side of the block. Good Luck,

The intake manifold on a 1990 Acura Integra connects to the head of the engine. Loosen all of the nuts from the manifold to the head, disconnect the throttle body, vacuum lines, fuel injectors and coolant lines then pull the manifold from the head.

Yes you can. But you will need to use a different intake manifold,one ment for a early model small block engine

passenger side of the block below the exhaust manifold if you lay under the truck flat on your back you would be looking right straight at it on the rear of the block towards the transmission

Follow the path from the exhaust port on the head. That will show you which is the exhaust rocker, which leads to the exhaust pushrod, which leads to the exhaust tappet.

The war of 1990 was Desert Storm

On a 1990 Jeep Wrangler, the IAT sensor is located on the intake manifold. It is a gray, two-wire system situated on the front of the manifold.

Elvis - 1990 The Storm 1-2 was released on: USA: 11 February 1990

The Desert Storm had started in 1990.

Storm and Sorrow - 1990 TV is rated/received certificates of: UK:PG

Differences with the rear main bearing, and the intake manifold angles

The Outsiders - 1990 Storm Warning 1-7 was released on: USA: 6 May 1990

No such thing as a O2 Sensor Box. The O2 sensor is located somewhere on the exhaust system. Looks similar to a spark plug with a wire connected. May be more than one. The o2 sensor on my 1990 Mitsubishi Mirage 1.5L (same engine as the colt i believe) is on the exhaust between the manifold and the catalytic converter

Answer Crawl under the car. You will see a muffler, and a catalytic converter which look similar. The converter is the one closest to the engine. If it's a 4 cyl. It should be between the exhaust manifold and engine pipe.