0
The housing retainer bolts are loose or the gasket has deteriorated. If replacing the gasket, use pliable gasket sealant to improve the seal. it could also be the water pump went bad and leaking water down beside the thermostat. the thermostat is part of the water
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Where is the coolant temperature sensor located on a 2006 Toyota Tacoma?
The 2006 Toyota coolant temperature sensor is located on the front of the engine. The coolant temperature sensor will be a few inches above the thermostat housing.
How do you replace the thermostat located on a 1998 Toyota Corolla?
The thermostat is located by the side of the cylinder block near the coolant inlet. Remove the coolant inlet housing after disconnecting cables and loosening the holding bolts. You will be able to remove the thermostat to replace it.,
How do you replace the thermostat located on a 2002 Toyota Camry?
To replace the thermostat in a 2002 Toyota Camry the vehicle battery must be disconnected and the engine coolant must be drained. The radiator hose is connected to the thermostat housing and needs to be disconnected. Next, remove all bolts and nuts for the thermostat housing unit. The new housing unit can now be attached along with the parts taken off.
How do you replace the thermostat located on a 1998 Toyota Rav4?
First the thermostat must be located on the 1998 Toyota Rav 4. The thermostat housing is on the left side of the engine under the exhaust manifold. The lower radiator hose flows directly to it. Drain the coolant, remove the hose and mounting bolts. Replace the thermostat from the inside of the housing and reinstall.
What are the Torque specs for 1995 Toyota thermostat housing?
The 1995 Toyota Tacoma thermostat housing torque specification is 40 pounds. The amount of torque on the thermostat housing bolts is not that important. You basically do not want to break the thermostat housing bolts.
Where is the thermostat on a 1990 Toyota truck?
Follow the upper radiator hose from the radiator to the engine. The thermostat will be located behind the thermostat housing at engine end of upper radiator hose. Drain some coolant into a clean container. Remove upper radiator hose from thermostat housing. Remove the 3 bolts that hold the thermostat housing to engine. Remove thermostat housing. Remove thermostat. Be sure to install the new thermostat facing in the same direction as the old one was.
Where is the thermostat on a 1990 Toyota truck 3.0?
Follow the upper radiator hose from the radiator to the engine. The thermostat will be located behind the thermostat housing at engine end of upper radiator hose. Drain some coolant into a clean container. Remove upper radiator hose from thermostat housing. Remove the 3 bolts that hold the thermostat housing to engine. Remove thermostat housing. Remove thermostat. Be sure to install the new thermostat facing in the same direction as the old one was.
How do you remove the thermostat of a 1999 Toyota corolla Ce?
Thermostat is located on side of cylinder block, behind coolant inlet housing for lower radiator hose and the generator. drain cooling system. rotate accessory drive belt tensioner clockwise to release tension from accessory drive belt. remove accessory drive belt. remove mounting bolts and generator. disconnect electrical connector from engine coolant temperature switch for removal of coolant inlet housing. remove nuts, coolant inlet housing, thermostat and gasket.
How do you replace thermostat on 1998 Toyota 6 cylinder?
Should be located in a removable housing at the engine end of the upper radiator hose Drain about 1 gallon of coolant from the radiator Remove this housing Note how thermostat is installed in housing Clean both surfaces Replace thermostat and gasket Re-install housing Re-fill coolant slowly to prevent an air lock Start engine and look for leaks Run engine to normal operating temperature with heater on Re-check coolant level
How do you change a thermostat on a 1993 Toyota camery?
Should be located in a removable housing at the engine end of the upper radiator hose Drain about 1 gallon of coolant from the radiator Remove this housing Make note how thermostat is installed Clean both surfaces Replace thermostat and gasket Replace housing Re-fill coolant slowly to prevent an airlock Start engine and look for leaks Run engine to normal operating temperature with heater on Re-check coolant level
Where is the thermostat located on a 1992 Toyota Camry 4 cylinder?
Follow the lower coolant hose from the radiator to the engine block. The housing where it attaches should hold the thermostat. Make sure you insert a new thermostat with the bleed nipple on the top.
Coolant leak at thermostat housing on Toyota sr5?
The housing needs to be removed. Check for scratches on the housing or engine. Make sure that all of the old gasket is removed before using gasket sealer to help seal the new gasket.
