0
Could you say that a shear lug assembly is the same as an anchor bolt and how would you explain your answer?
Wiki User
∙ 8y ago
- Shear lugs are small steel members welded or brazed to parent structural members prior to encasing them in concrete or other material. These lugs hold this encasing material with the steel member for environmental protection and also give the desired shape to the structural members.
- Anchor bolts are the ones which are fixed with the parent structural member to hold or support external objects/loads to the parent member. Fixing can be chemical or mechanical depending on the material on which it is anchored.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
What are the purposes of providing shear reinforcement in beam . Explain with suitable sketch?
beams is tying
How do you improve the result of the experiment shear force?
u could improve it by not forgetting to repeat it.
What is the ratio of average shear stress to maximum shear stress for a circular section?
the average shear stress is 3/4 the maximum shear stress for a circular section
Introduction of chip thickness ratio and shear plane angle during machining?
shear plane angle is Eric siangco + hulian lastontas = shear plane angle
How does shear strength of fine sand effect by void ratio?
Shear strength of fine sand is determined by the angularity of the sand particles, the grading of the sand. These two features governs the critical state shear strength parameters of the sand. Density, however, dictates the peak shear strength of the sand. i.e. the denser the sand, the higher the peak shear strength. But the critical shear strength remain the same. The denser the sand, the lower the void ratio. Shear strength of fine sand is determined by the angularity of the sand particles, the grading of the sand. These two features governs the critical state shear strength parameters of the sand. Density, however, dictates the peak shear strength of the sand. i.e. the denser the sand, the higher the peak shear strength. But the critical shear strength remain the same. The denser the sand, the lower the void ratio.
What is the shear strength of anchor bolts?
Generally speaking, shear strength is 60% of the ultimate tensile strength of the anchor bolt. Please see the related link for more information as well as a table of common material strengths.
Why does the USMC EGA have a hole in the left anchor fluke?
It's not a hole, it's a rivet. In the event that the anchor becomes stuck the rivet will shear before breaking the anchor, thus setting the anchor free.
What are the purposes of providing shear reinforcement in beam . Explain with suitable sketch?
beams is tying
Explain in detail about the BMdiagram?
The BM diagram can help you in the calculation of the shear force and the bending moment.
How could you find out whether the shear strength depends on direction in which the paper is torn?
bcause shear stength measure in mass
Why riveting is used in aircraft assembly?
rivets are used in aircraft structure primarily to take shear loads and gives initial stiffness
Who found out you could shear sheep?
the person who invented the scissors
Types of Shear wall - Explain?
A shear wall does two things. It acts as a brace that will not allow the wall to lay down accordion style. It also acts as a barrier to projectiles in a high wind situation. A shear wall is an INTERIOR wall that is lined one side with plywood, from exterior wall to exterior wall.
Relationship between the shear stress and angle of shear?
Shear Stress divided by the Angle of Shear is equals to Shear Stress divided by Shear Strain which is also equals to a constant value known as the Shear Modulus. Shear Modulus is determined by the material of the object.
Is it safe to drive on bad wheel bearings?
No, no and did I mention NO(?)!Worst case failure is the wheel comes off.You want to risk it?...Get 'em checked, get 'em replaced.No, wheel could seize, spindle could shear off No, wheel could seize, spindle could shear off
Does friction mean the same thing as shear?
No. Friction is a measurable force observed between two objects sliding/rolling along each others surface. Shear is the act of cutting. The process of friction could shear something. Think glaciers.
What is a homophone for shear?
A homophone for "shear" is "sheer".
