0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you replace the rear wheel bearings on a 1967 Pontiac Firebird 400?
remove rear cover from differential, find 1/4 inch bolt in the third member that holds the 1 inch diameter pin between the axles. Remove the bolt and the pin, push the axle that you want to remove in towards the differential and remove the C-clip that keeps the axle in the differential. Pull the axle, using a bearing puller remove the oil seal and the bearing. Replace the bearing and the oil seal, make sure it is installed in the right direction or it will leak. install the axle, C-clip, pin, bolt, rear cover, and differential oil.
How do you replace the rear wheel seal on a 1992 Chevy blazer?
You have to open the differential and remove the retaining pin from the spider gear to remove the axle shaft.
I'm trying to replace the wheel speed sensor on the differential. does anyone know where it is and how to replace it?
It is on the top of the rear axle. You remove the nut that holds the brake line, remove the hold down bolt, and pull sensor out.
Whats the rear differential 1999 Tahoe?
The rear differential is where the driveshaft meets the axle. Its right in the middle of the axle and is about the size of a basketball.
Where is the rear differential on a 1999 Chevy 1500?
Inside the rear axle.Inside the rear axle.
How do you remove rear axle 2003 gmc Yukon?
Remove wheel, Remove drum or disc brake rotor,remove rear differental cover. Remove shaft between the spider gears that is held in by a lock bolt. Shove the axle from the outside toward the differential and remove the "C" clips that hold the axle in inside the diff. and then the axle can be removed.
99 Toyota 4runner replace rear axle bearings?
Remove the rear wheel from the axle. Remove the brake pads and hardware. Remove the axle end cap. Remove the bearing. Reverse the process to install the new bearing.
How do you replace the rear differential bushings on a 2001 outback?
The first step to replacing the rear differential bushings on a 2001 outback is to gather the necessary tools and materials. To complete the project you will need a hydraulic jack a ratchet a socket set a torque wrench new bushings and an axle puller. Jack up the car Use the hydraulic jack to raise the car off the ground and support it with jack stands. Make sure the car is secure and wont move. Remove the axle shaft Use the ratchet and socket set to loosen and remove the axle shaft bolts. Then using the axle puller remove the axle shaft from the differential. Replace the bushings Remove the old bushings and replace them with the new ones. Make sure the bushings are properly aligned and seated. Reinstall the axle shaft Reinstall the axle shaft and use the torque wrench to tighten the bolts to the correct specifications.Once the new bushings are installed and the axle shaft is secured you can lower the car and test drive it to ensure that the differential is functioning properly.
Is it hard to replace the rear axle seals on a 1993 Chevy silverado?
Remove wheels Remove brake drums if so equipped Axle shaft should be secured by 4 bolts accessible by hole in center hub Remove these 4 bolts and axle should slide out of differential Bring to an auto parts/machine shop to replace seals Not necessarily the way to do it above: Chock front wheels and raise rear wheels, remove wheels and brake drums, remove rear differential cover and drain fluid, spin left or right tire to achieve shear pin stop bolt, remove this bolt, and remove shaft gear pin, push in on left then right axle while c clips fall into pumpkin housing, remove axle shafts, remove rear axle seals from housing using the axle itself or a seal remover, and replace. Installation is reverse of removal. Don't forget to fill the diff. with fluid, some newer chevys take a special fluid fyi.
How do you replace a rear right axel in a 2002 4x2 Chevy s-10 pick up?
You have to take the differential cover off and remove a C clip that holds the axle shaft. that will allow you to pull out the axle (****** note the number of splines on the axle if ordering part!!!!)
What is the purpose of inter axle differential?
The inter axle differential (also called a power divider) is an integral shaft in the forward axle. That shaft is the input for the forward axle and also the rear axle with a differential separating the input from the output allowing for a difference in speed between the front and rear axle.
What is the purpose of inter-axle differential?
The inter axle differential (also called a power divider) is an integral shaft in the forward axle. That shaft is the input for the forward axle and also the rear axle with a differential separating the input from the output allowing for a difference in speed between the front and rear axle.
