0
No, on most newer cars you also have to press the brake pedal to shift out of Park.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Why do your headlights come on when you press the brake pedal on your 01' s10-blazer?
The only way your headlights can come on when you press on the brake pedal is a crossed wire. The brake light wire and the headlight wire can be frayed and touching each other.
How can you get a Ford Windstar shifter out of park?
You are supposed to only have to press the brake pedal. Evidentally your brake lights aren't working. You probably need to see if the brake light switch is bad.
Why does the brake light not light up on 1997 Quest when you turn on the light but it light when you brake?
Brake lights only come on when you press the pedal. The brake light is either a different bulb or filament in a dual-filament bulb than the tail light.
Hello, I have a Dodge Ram 1500 and my foot keeps slipping off the brake pedal is there any was I can install a larger brake pedal or adjustable pedals?
no, the only brake pedal you'll ever have is the small one. maybe get bigger shoes
What causes only one brake light to stay on even after the the brake pedal has been released?
because it does
Why do the brake lights on a 1992 Mustang only come on when the brake pedal is pushed all the way to the floor?
The brake light switch is out of alligment. Check on the brake pedal arm and readjust the switch.
Where is the fuse for the emergency brake?
The fuse for an emergency brake is located under the brake pedal. However, it is only on the drivers side of the vehicle.
What are symptoms of a bad power brake booster?
hard brake pedal is the most obvious sign only way i know to test a booster, is to turn engine off. use brakes several times till pedal is hard. then with brake applied,start engine. the brake pedal should then soften.if the pedal stays hard the booster is bad
What is wrong when tail lights work on a 1995 Nissan pickup but the brake lights don't work?
Its the brake switch on the brake pedal. Its a plunger like switch, its usually the only thing on the brake pedal. Its pretty easy and cheap to change.
What causes brake pedal to go half way to the floor on a 1999 ford explorer?
Something is impairing the brake pedal to go to the floor. Only a mechanic can tell you what is happening.
On a 1987 Honda Accord why would the brake pedal vibrate when you press the it at 35 mph if you have replaced the rotors three times and it did not help?
AnswerUsually a pulsating brake pedal is an indication of a warped rotor. When you replaced the rotors did you torque the lug nuts to the proper specs, (80 ft lbs)? If not then you are warping them each time. Also make sure you tighten in a criss cross pattern. Of course you need to check each and every rotor for trueness. Also a warped wheel can cause this. Check all your wheels for a bent condition.If your brake pedal is pulsating. You might have a out of round rear brake drum. When your front rotors are warped you will feel it in your steering wheel. Try this test. lightly rest your foot on the brake pedal, with your foot resting on the pedal slowly apply your E brake. ( your E brake only works your rear brakes) If your brake pedal pulsates the problem is in the rear brakes.
What does the symbol of a foot on a pedal with 2 half circles mean?
POWER ADJUSTABLE FOOT PEDALS. This is what it means. I searched all over the internet, and found no answers, until I looked at a Ford Crown Victoria manual. The following instructions are for Ford Crown Victorias. The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal. • Press the right side of the control to adjust the pedals toward you. • Press the left side of the control to adjust the pedals away from you. The adjustment allows for approximately 2.5 inches (65 mm) of maximum travel. Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.
