answersLogoWhite

0


Best Answer

No, it does not have a crank sensor. the optispark (distributor) does the job that a crank and cam sensor would do for that model of Camaro. they added one for sure in 1997 I know that because I have had a 93 94 95 and 97 Camaro z28

not sure if 96 has one or not I haven't had one of those to work on but they are real easy to find on the models that have them they are located at the bottom of the timing cover and have a 3/8 bolt that holds them in.

User Avatar

Wiki User

11y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Does a 95 Z-28 Camaro have a crank sensor?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Art & Architecture

What are the main problems with 95 buick rivieras?

Crank Pulley, crank sensor, ignition module, dirty maf sensors, clogged fuel filters.


Is there a map sensor on a 95 aurora?

Yes, about 50-60 dollars from Advance auto


What are differences with block and cylinder heads from 93 vortec 4.3 and a 95 vortec 4.3 and would mixing them cause crank but no start?

I bought a 95 S10 Blazer w/ L35 Vortec and put a 92 4.3 Vortec into it. The blocks a mostly the same. the timing cover flange is different then the 92 or 93 vortec. If u use a block older the a 95 then Put a lot of RTV around the bolt holes on the cover-to-block mating surface. The heads are also different. There is one hole, a knock or coolant sensor, in the 94 and older heads. In 95 the Drivers side has 2 sensors, I coolant and 1 knock sonsor. The 94 and older engine had the knock sensor at the back of the head on the block. In 95 the passangers side head didn't have any major changes. The 95 S10 Blazer(compared to the 92 S10 Blazer has different: timing cover w/ crack sensor, distributor with cam sensor (non HEI-style), 2-sensor holes in drivers side head, Slightly different lower and upper intake. Lower intake has a pin that a distrubutor postitioning arm, It keeps the distributor locked into a certain position. and the upper intake has a bigger hole for the IAC valve's plunger. don't use an older IAC valve from an older 4.3 Vortec, There different. If you can us a block out of a 96 and switch everything else to the 96 block. The 96 has reinforcing ribs from the water pump to the lower corner of the block on both sides. My 95 Blazer runs really nice with the 92 block and rebuilt 95 heads on it. At least until it stalls. The thing warms up and then stalls. I cant find the problem. I have replaces Cap, Rotor, Plug, Wires, Coil pak, Fuel pump, Crank sensor, Both drivers and passengers side Knock sensors, both Coolant sonsors (side drivers head and lower intake sensor). Put a 92 Egr valve on it not the same autozone part#, but it didnt affect the way the engine runs, if anything ran better with the 92 on it( it was cleaner).


Where location of a camshaft sensor GMC Sonoma 95 4.3 V6 Vortec?

The sensor is down on the front of the oil pan just behind the crankshaft pully, which is located at the front of the engine.


Is there a reset for the fuel pump on a 1995 Chevy camaro I ran out of gas and the car won't start even with plenty of gas I don't hear the fuel pump when you turn the key?

I ran out of gas with my 95 camaro and filled it up and started fine. Sounds like it may be a bad fuelpump/relay or fuse. Check the fuse and the relay. Any luck on figuring this out? I'm about to spend a grand!