0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why do you need to set the clock rate on some interfaces and do not need to set the clock rate on other interfaces?
Clock rate must be set on an interface that is the DCE. This provides clocking for the DTE and helps with data transmission across the connection.
Why set clock rate in router?
To configure the clock rate for the hardware connections on serial interfaces such as network interface modules (NIMs) and interface processors to an acceptable bit rate, use the clock rate interface configuration command. Use the no form of this command to remove the clock rate if you change the interface from a DCE to a DTE device. Using the no form of this command on a DCE interface sets the clock rate to the hardware-dependent default value.
What are the three best ways to see if your routers serial port is dce or dte end?
1. The command show controllers serial [interface number]can be used to determine whether your serial interface is a DCE or DTE interface. An abbreviated listing of the displayed results for the show controllers serial 0 command is shown. The Serial0/0 interface is a V.35 DCE cable. This command should be used when you have an RJ-45 connection.2. The V.35 cables are typically labeled to indicate whether they are a DTE or DCE cable.3. Inspect the end of the V.35 cable to determine whether it is made (DTE) or female (DCE)
Is the DCE end of a v.35 cable female?
yes.. DCE is the female connector wereas DTE is the male
Is the DCE end of a v. 35 cable female?
yes.. DCE is the female connector wereas DTE is the male
What type of serial cable of DTE or DCE is connected to a synchoronous serial port on a router?
Any of them might be connected to a router, but if it connects to a piece of equipment provided by an ISP, usually the ISP's equipment will have the DCE connection, and the router will have the DTE connection. The DCE connection is the "master" part - the part that controls the transmission speed.Any of them might be connected to a router, but if it connects to a piece of equipment provided by an ISP, usually the ISP's equipment will have the DCE connection, and the router will have the DTE connection. The DCE connection is the "master" part - the part that controls the transmission speed.Any of them might be connected to a router, but if it connects to a piece of equipment provided by an ISP, usually the ISP's equipment will have the DCE connection, and the router will have the DTE connection. The DCE connection is the "master" part - the part that controls the transmission speed.Any of them might be connected to a router, but if it connects to a piece of equipment provided by an ISP, usually the ISP's equipment will have the DCE connection, and the router will have the DTE connection. The DCE connection is the "master" part - the part that controls the transmission speed.
Is clocking for the serial port on a router at the DTE end?
(DCE) Data Communications Equipment (the serial interface responsible for clocking) (DTE) Data Terminal Equipment (the serial interface designed for connection to a CSU/DSU to outside digital communication service)
What is the purpose of a DCE in computer Networking?
When you're using serial cables in routing you need a DCE side and a DTE side and both have to be timed just right for it to work.
How do you know which COM Port Number is assigned for a cable?
Dce cables and dte cables through you can connect.
What command will show you whether a DTE or a DCE cable is plugged into serial 0?
sh controllers s 0
Why use a clock rate of 64000 for serial interfaces?
When two routers are connected to communicate using a serial cable connection, one end of the router will be using DTE (Data Terminal Equipment) and the other end uses DCE (Data Communication Equipment). In order to communicate effectively with out any delay or to have the same band width, we use 64000 clock rate. This answer is given with the knowledge what I have, please update me if I am wrong. Thank you Syed
What DTE devices are used on WAN and what DCE devices are used on WAN?
DTE devices in the sense we have PC (Computers), router,Serial Printers, PLC's, Video Cameras, Video Recorders, Video Editors like this we use any of them depending on our requirementDCE devices in the sense hub,bridge,switch,modem etc are dce devices we usei hope it is useful to you........
