answersLogoWhite

0


Best Answer

Anywhere in between. The farther open valve is the warmer radiator will get during normal operation of heat system.

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Does a radiator in a water-to-steam boiler heating-system need to be all the way open or all the way closed or can it be in between?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How does heat get from inside the boiler to the wall behind the radiator?

Conduction of heat energy from the source to the water in the boiler. A pump moves the hot water to the radiator.The heat radiates out from the radiator to the air, where convection then circulates it through the room.


Boiler System Repair?

form_title=Boiler System Repair form_header=7043 Please describe the type of boiler system which needs repairing*= () Natural gas fired () Propane gas fired () Oil fired () Electric fired How would you describe the nature of the problem? (Select all that apply)*= [] Gas smell [] Power failure [] No heat in one location [] No heat in all locations [] Cracked radiator [] Leaky radiator [] Leaky boiler [] Pilot light out on boiler [] Broken baseboard radiator cover [] Radiant heat pump not functioning [] Hammering noise in radiator [] Too much heat in some locations [] Annual/Preventative Maintenance


How do you drain your baseboard radiators?

If there is no drain valve at the radiator you can drain the system at the drain valve on the boiler


How does the water flow in an old cast iron radiator?

The boiler has a circulation pump that circulate the water


How to drain a radiator in the house?

Not for the faint of heart! For a Combi/Evaporation boiler: Switch off the boiler. Take a reading of the boiler water pressure gauge. Shut off the radiator's thermostat valve(if fitted)/supply valve and return valves, connect a hose to the drain and put the other end into a large container below the level of the bottom of the radiator. Open the draincock first and then the air bleed valve and let the radiator drain. Close the draincock. When refilling the radiator put the anti-corrosion treatment in first then open the thermostat valve and return valve as wide as possible. when the air is expelled, close the air bleed screw. Using the fill loop restore boiler pressure. Put all thermostat valves(if fitted) to max and fire up the boiler. After the boiler has run for 10 minutes, switch off, or so go to the highest radiator and bleed out the air. WARNING: the water/steam will be very hot and likely to spit. Use a cloth as a barrier and to mop up any spills. Recheck the boiler pressure and top up as necessary.


What is the difference between a shell type boiler and a sectional type boiler?

7


Explain why the boiler and pump are a model for the cell in a circuit?

think of a circuit with a cell , wires and a bulb. now think about a boiler and pump, pipes and a radiator. the cell is like the boiler and pump because it has the energy. the pipes are like the wires because they transfer the energy. the bulb is like the radiator because they use the energy changing it into light energy and heat energy when referring to them especially.


Do the thermostat have to be on to bleed home radiator?

on hot water heat with a boiler you should pressurize the system then open the bleeders


What is the difference between steam boiler and pressure vessel?

Boiler is basically a pressure vessel in which this boiler aims to heat the surroundings which is a pressure vessel.


What is the difference between lancashire boiler and cornish boiles?

The Cornish Boiler only has one fire tube compared to the Lancashire Boiler's two.


Boiler & Radiator Heating Installation?

form_title=Boiler & Radiator Heating Installation form_header=7033 Do you want additional thermostatic controls in certain rooms?*= () Yes () No Would you like to know more about the project's green alternatives ?*= () Yes () No Please specify the type of boiler system to be installed.*= () Natural gas fired () Propane gas fired () Oil fired () Electric fired () Want Recommendation


What is the maximun radiators that can be used with a boiler with max 40000 Btuh output?

Depends on how many sections of the radiator and the height and width