answersLogoWhite

0

No, it will decrease slightly.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

How can you get more horsepower on your 96 Impala?

cool air intake, dual exhaust, turbo, superchip, engine spacers, and ther tons of other applications.


What does a egr valve do?

The EGR (Exhaust Gas Recirculation) directs exhaust gasses into the engine's combustion chamber via the intake manifold. The exhaust gasses are inert (do not support combustion) and displace oxygen that would normally be drawn into the engine during the intake stroke. Think of the engine as a vacuum pump and can only draw in a fixed amount of oxygen to be mixed with the fuel for ignition. The reason that exhaust gasses are drawn into the combustion chamber is to cool the exhaust. With less Oxygen in the fuel mixture the flame burns cooler and cooler exhaust temperatures result in lower NOX (oxides of nitrogen) emissions.


Why is copious dribble coming from exhaust of dirt bike?

It could be condensation from hot exhaust gases on the cool exhaust pipe.


My exhaust was very loud until i hit a bump and now the noise went away?

Well this could be cause by many things. First off it could be caused by your caddlic convertor being clogged. second your muffler could have been loose and the bump knocked it into place. Third it could have been caused by your cool air intake, if your cool air intake hose was not properly in place it could have caused your engin not getting enough air intake.


Are the inlet valves made of the same material as exhaust valves or have different treatmnet?

Most intake valves are made of the same material as the exhaust. They are heat resistant treated high carbon steel, as are the valve seats. The exhaust valve is usually larger in diameter to aid in scavenging of the spent hot exhaust gas. Some more expensive engines have sodium (Na) filled exhaust valves to aid heat transfer to the valve seat to help cool the valve.


Why do you need the intake vent going to the outside for portable air conditioners I do understand the need to vent the warm air but can't the intake take from the room?

You can, in fact only use the exhaust hose and let the unit draw air from the inside, but you would lose the efficiency benefit gained from buying a dual hose unit. The air it draws in is air that you have already paid to cool. It would draw this air inside the unit to cool the compressor and the condenser coils. Then it would exhaust that air outside. With two hoses, it is using the warm, outside air to cool the air conditioner coils, so you are not paying to cool the components, only the air in your room. I strongly recommend using both hoses.


How do you replace intake manifold gasket venture?

Elmo is cool


Why does the amount of daily intake vary between individuals?

it cool


What is the purpose of a cold air intake?

The main purpose of cold air intake is to increase mileage. As the engine takes in cold air instead of warm, the engine cools down and more energy can be used to run the car instead of having to use up the energy cool it.


What does an exhaust system expansion box do?

An exhaust system expansion box allows for the cooling of extremely hot air. The hot exhaust is cool in the expansion box before exiting the tailpipe.


Why does hot weather exhaust you?

Hot weather can exhaust you because your body has to work harder to regulate its core temperature. In order to cool down, your body increases blood flow to the skin and sweats, which can lead to dehydration and electrolyte loss. This extra effort can leave you feeling tired and fatigued.


How do you adjust rocker arms on 04 dodge diesel?

You need a .010 (intake) and a .020 (exhaust) feeler gauge first off. I can't remember the torque specs so look them up. With the valve cover off the first rocker will be intake followed by exhaust, repeat times 6. Bar the engine over in normal (clockwise) direction as viewed from the front of the engine until #6 valves are in overlap (bar the engine over a couple of times and watch the valves open and close, there will be a point when the exhaust valve starts to close and the intake starts to open, both rockers will have tension on them, this is overlap). With #6 in overlap you can start at #1, both the intake and the exhaust valves will be "loose" meaning you can move them up and down a little bit. The firing order is 1-5-3-6-2-4. 1 and 6, 2 and 5, 3 and 4 are companion cylinders meaning that they go up and down at the same time but are 180 degrees out. Set this up as 1-5-3 6-2-4 This works with any four stroke firing order to find the companion cylinders. This is needed to know which stroke the other cylinders are on to adjust them. If 6 is on overlap (just finished exhaust stroke, going to intake) 1 will be on power and both valves closed completely. Caution!!! Do not run the overhead with the engine hot. The valves will shrink when they cool causing your adjustment to be completely off. Make certain you use the .010 on intake and .020 on exhaust, do not mix them up! Do not bar the engine over counterclockwise. This will remove and reverse the gear lash and your adjustment will be off, better to bar the engine over another full rotation than to bar it backward. If you have never used feeler gauges or are not mechanically inclined I really recommend taking your truck to a pro. So, with #1 in power (#6 in overlap) you can adjust #1 intake and exhaust, #2 intake, #3 exhaust, #4 intake, and #5 exhaust. Bar the engine over so that #1 is in overlap (#6 in power) and you can adjust #2 exhaust, #3 intake, #4 exhaust, #5 intake, and #6 intake and exhaust. Sorry if this is too much info but I have had to rebuild too many of these things due to people's lack of knowledge and I would hate for anyone to mess up their engine.