0
In general, you will get the best performance if you put the largest module (in megabyte size) in the lowest-numbered slot. For example, if your computer comes with 32MB of removable memory and you want to add 128MB, it would be best to put the 128MB module into slot 0 and the 32MB module into slot 1.
What else can I help you with?
Where is the sync button on the new xbox 360?
Do you know where the two slots are to plug in controllers? If you do it is the little black button next to it. Did i solve your problem? YES!
How do you replace 4x4 control module in 2002 ford explorer sport trac?
The 4x4 control module is located behind the kick panel in the passenger side floor board. The module simply unplugs and you plug the new one in.
How do you add memory with diagram?
To add memory to a computer, you typically install RAM (Random Access Memory) modules into the motherboard's memory slots. First, ensure the computer is powered off and unplugged. Open the case, locate the RAM slots, and carefully insert the new RAM module at an angle, pressing down until the clips click into place. For a visual reference, a diagram would show the motherboard with labeled RAM slots and the orientation of the RAM module during installation.
Where is the ignition control module located on a 1992 Chevy Berretta?
ignition module is located under the distributor, where the spark plugs come out to go to the spark plugs, remove 6 bolts that hold the 3 capped distributor on, unplug the wires from both ends of module, 3 plugs, lift module out, nothing holds it in after distributor is removed, plug new module in, replace distributor.
How do you fix the ignition module on a 1990 Chevy s10?
remove distribtrer cap,remove distributer.un plug from pick up coil.remove two bolts holding module..must use dielectric lube supplied with new module...coat entire metal surface before installing new module..distributer must be at top dead center when installing distributer unless you marked posision of rotor prior to removing....
How do you change a control module 1988 Chevy 350?
Loosen the two latches on distribitor cap lay cap to the side unplug electrical plug from module then take the two small bolts and remove module. Reverse process to install new one be sure to to put a high temp lithium grease on base or shiny part of module.
93 Chevy Lumina Euro Sedan It will crank but not fire What could be wrong?
Ignition module. See if spark plug wires have arched. Check for spark. You could change it yourself. Module plus new wires will cost you around $200.
What is the problem with a 91 Corsica that dies when it gets wet?
I know on an 89 Beretta The ignition control module in on the block underneath the front exhaust manifold...I changed the module and plug wires and it seemed to be ok for me. The ICM is where the spark plug wires come from. Try to get new spark plug wires that make a better seal and make sure the connectors are plugged into well and there isn't any corrosion. Hope this helps.
How do you replace the Ignition Module in the Chevy Celebrity?
To replace the ignition module in your Celebrity: Unplug the wires, take note of where they go so you can put them back in the correct place. Remove the screws that hold the ignition module in place. If the old module was coated with dielectric grease on the mounting surface put fresh dielectric grease on the replacement ignition module. Put the new ignition module in place and attach with the screws. Plug the wires back in their respective places.
Is it possible to increase the number of available PCI slots on your?
If you wanted more slots im pretty sure you would have to install a new mother board with more PCI slots
How can you provide new ports without expansion slots on the motherboard?
You can use USB adapters. But USB does not cover as many interfaces as expension slots.
Where is the daytime running light module on a Canadian crown Victoria - can't get them to turn off no matter what is unplugged even the headlight switch?
Under the hood, on the left bolted to the radiator frame is a small box about 5" wide, 4" high and 1 1/2" deep - unplug it and plug in a new one - it should solve the problem.
