answersLogoWhite

0


Best Answer

Strip the wire to desired length. Then hold the wire horizontally and hold the soldering iron underneath the stripped part while holding the solder on the top of the wire. When the wire gets hot enough it will suck the solder into the wire

User Avatar

Wiki User

โˆ™ 2009-10-10 17:28:29
This answer is:
User Avatar
Study guides

Add your answer:

Earn +20 pts
Q: Explain how to apply tinning technique in soldering?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Engineering

What procedure is best for soldering joints?

There are several ways of soldering electrical joints. Automated methods use wave soldering in which a circuit board is passed over a bath of solder. Re-flow soldering uses solder paste that is applied to the circuit board and then heated in an oven until it melts and flows across the joint. Manual soldering is largely still carried out with hand held soldering irons. The standard technique is to apply the tip of the iron to the joint and then feed solder onto the joint as the iron heats it. This method allows the solder flux to flow around the joint before it is affected by the heat. Applying the solder to the iron before touching the joint will often result in a dry joint because the flux will burn away and evaporate before it reaches the joint. Most electronic components have limits for the amount of time the soldering iron can be in contact with each pin. Generally it is in the order of 5 or 6 seconds. With the introduction of lead free solder, temperatures need to be higher to get a good joint and therefore the contact time with each component is reduced. With a shorter contact time, it is even more important to heat the joint and apply solder in an efficient manner. Production and commercial soldering skills take years to develop with apprenticeships lasting up to three years. To describe soldering techniques in just two or three paragraphs is to merely scratch the surface. Although there are many written instructions for soldering joints, there is no substitute for practice and learning from skilled wiremen.


How much volt apply to instrument cable meggering?

500v


What is the purpose of soldering flux?

Very simply flux reacts with surface corrosion and washes it away, making the metal surface being soldered easier for the solder to wet and producing a more solid and reliable joint, both mechanically and electrically. Acid flux is more aggressive and acts faster than rosin flux, but must be washed off completely with water as soon as the joint cools because the acid will slowly attack the metal of the joint. As electronic circuits usually should not be washed with water, only rosin flux should be used on electronics because it can be left on the completed joint without damaging it.


By when would an in-state engineering major have to apply for Fall acceptance?

February


Why is there a difference in current in a coil when you apply dc voltage and then AC voltage to it?

A coil has both resistance and inductance. When you apply a d.c. voltage, the opposition to current is the resistance of the coil. When you apply an a.c. voltage, the opposition to current is impedance -the vector-sum of the coil's resistance and its inductive reactance. Inductive reactance is proportional to the inductance of the coil and the frequency of the supply.

Related questions

What is meant by tinning stranded wires?

It is a reference for the preparation for soldering a stranded wire so you get a good joint. You twist the strands together, heat the wire with a soldering iron or gun and then apply a small amount of solder on the tip of the wire and it melts into the strands. Then you can solder the wire to another like wire or to a terminal or whatever. You basically reheat the wire to make connection and can add more solder as needed.Additional informationTinning is also useful if the wire is to be put in a "screw lug". The term "tinning" comes from the fact that older solder contains lead and tin. Some of the newer solder is supposed to be lead free.


What are the four steps for correctly soldering components to a printed circuit board?

1. Remove the soldering iron from the holder and wipe the tip on a sponge. 2. Heat the joint to be soldered. 3. Apply solder to the joint. 4. Apply a small bit of solder to the tip of the soldering iron and return it to the holder.


What is the Thurstone technique?

The Thurstone technique is a technique that allows subjects to express their beliefs or opinions by checking items that apply to them.


What is the name of the technique where you apply thick paint?

impasto


Whose technique did Josh Graves apply to the Dobro?

Earl Scruggs (; Chibi


Which troubleshooting technique should you apply if you are having problems with your motherboard?

Record error messages


Sample of letter of intent to apply for a supervisor position?

In a letter of intent to apply for a supervisor position, you will want to explain your qualifications. Also explain how you will help the business positively.


Why did you apply for this position' in a job interview?

Explain what attracted you to apply for the job/position , explain your personal qualities that will help you succeed in the position, why the position interests you, and why you deserve the position.


What procedure is best for soldering joints?

There are several ways of soldering electrical joints. Automated methods use wave soldering in which a circuit board is passed over a bath of solder. Re-flow soldering uses solder paste that is applied to the circuit board and then heated in an oven until it melts and flows across the joint. Manual soldering is largely still carried out with hand held soldering irons. The standard technique is to apply the tip of the iron to the joint and then feed solder onto the joint as the iron heats it. This method allows the solder flux to flow around the joint before it is affected by the heat. Applying the solder to the iron before touching the joint will often result in a dry joint because the flux will burn away and evaporate before it reaches the joint. Most electronic components have limits for the amount of time the soldering iron can be in contact with each pin. Generally it is in the order of 5 or 6 seconds. With the introduction of lead free solder, temperatures need to be higher to get a good joint and therefore the contact time with each component is reduced. With a shorter contact time, it is even more important to heat the joint and apply solder in an efficient manner. Production and commercial soldering skills take years to develop with apprenticeships lasting up to three years. To describe soldering techniques in just two or three paragraphs is to merely scratch the surface. Although there are many written instructions for soldering joints, there is no substitute for practice and learning from skilled wiremen.


Can you mend exhausts by soldering?

Welding or brazing perhapsReplacement is best Solder has too low a melting point to be good in such a high temperature environment. After running the car for a few miles, you could apply the solder to the muffler and it will melt without a torch or soldering iron.


Resins that could make textile into bullet proof by coating or laminating technique?

how to apply it on the car


Which massage technique is used when you first apply shampoo?

The technical term would be circular effleurage.

People also asked