0
The fiero front hood release cable has an extra cable tucked inside the release lever housing. If they're both broke then you'll have to use a crowbar and lightly pry up on the hood but be extremely carefull not to break the fiberglass hood. Take a long flat tipped screw driver and remove the foam padding around the latch then take a 10mm stubby wrench and remove the 2 bolts holding the latch to the car then just raise the hood and trip the latch. Remove the old cable and install a new one.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Where is the bonnet release on an 88 fiero?
The front hood release leaver is under the dash near the door. the tail hood release is a grey button on the right side of the gauge cluster.
Where are the fuses for a 1984 Pontiac fiero?
the fuses in a pontaic fiero are near the front hood release, it is a black box looking thing that has a button on the front. when you press the button the tray of fuses release and fall down in a near 90 degree angle.
Does 1986 Pontiac Fiero hood raise from the front or the back?
The front hood raises from the rear or windshield end, the rear hood raises from the rear or bumper end
Where is the horn located under the hood of a 1986 Fiero?
The horns (2) are located at each side under the headlights in the front clip
How do you change a hood release cable on 87 fiero gt?
This is kind of neat: The fiero comes with a second cable already installed. Remove the hood release handle and there should be a cable end hanging there. Pull and release the hood. The replacment proceedure is undo damaged cable from hood latch, tape the new to old, follow the camle to the bulkhead and release all the hold down clips and gromits, use the old to fish the new through the car, re-conect.
How do you open the front hood of a fiero if both cables aren't working?
Your cables may just be broke, but more likely, if your Fiero has been in a front end collision your hood may have been pushed back toward the windshield. There are two safety locking "pins" one on each side near the windshield that will keep the hood from being pulled up(why thy chose to do this on a hood that couldn't "fly open" I will never know). If you think this is the case with your Fiero you can pull up the headlight covers with the help of a friend(It's not connected to the headlight assembly but is spring loaded), to gain access to some of the hood hinge nuts(just to the inside of the light assembly). There is very little room to work but loosening these may give you enough slack to slide the hood forward and release the tension on the latch or to disengage the hood from the safety pins. Haveing a friend push down on the hood where the latch is while you pull the release cable may also help. Hope this helps.
Where is the build code location on a 1988 Fiero GT?
If you mean the plant code it is 11th number in the VIN If you mean the sticker with the options, it usually under the front hood stuck to the inside of the hood, BUT I have seen a few on the underside of the rear hood.
How do you open the hood of a 1994 Chrysler new yorker?
Pull on the hood release handle under the dash driver side. Then go to the front of the car, lift the hood slightly to access the secondary hood catch. Release it and open the hood.Pull on the hood release handle under the dash driver side. Then go to the front of the car, lift the hood slightly to access the secondary hood catch. Release it and open the hood.
Where is hood release for 1980 VW rabbit truck?
If you are standing in front of the truck it should be the little tab sticking out from the front of your hood. just push it too the side and release the hood by means of the handle you can then reach underneath your hood
Where is the hood release on a 1986 Pontiac Fiero?
It is located left side of the instr. panel on the bottom... flush mount... do a headstand and look under the dash and there it is!!!
How do you open the hood on a 1975 trans am?
By pulling the hood release under the front of the car.
Ohow do I open ford explorer hood with dead battery?
Pull the inside hood release and then go to the front of the Explorer and press down on the hood slightly while operating the auxillary hood release located just under the front edge of the hood at the center
