0
Flat side should be top or bottom for eccentric reducer in vacuum line?
GVVENKATESH1
Doesn't matter
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is double glazing is and when is it used?
Double glazing is where two sheets of glass are placed together in a frame with a vacuum between the panes. The vacuum prevents cold entering from the outside and warmth existing from the inside. Therefore it is normally used for external windows and doors. Note. It also acts a noise reducer and some houses near airports and their flight paths even have triple or quadruple glazing to reduce aircraft noise.
Can you assign temperature to a vacuum?
Answer Yes, you can. I think the answer is no. A physical object in a vacuum can have some energy/heat in it, and the energy associated with electromagnetic radiation can have energy/heat associated with it, but the vacuum itself cannot. ______________________________________________________________________ There is no such thing as a vacuum.
Was the vacuum invented by ives mcgaffey?
It was I. I invented the vacuum. Who am I? Your mother.
How do you make a vacuum pump?
I think you have to make it out of plastic then connect to the vacuum
Why need to vacuum in transformer chamber before filling transformer oil and how long need to vacuum?
we need vacuum to remove moisture from tank
Should the number stamped on housing of a Kirby vacuum match the sticker number on bottom of Kirby model?
Should the number stamped on housing of a Kirby vacuum match the sticker number on bottom of Kirby
What pool vacuum is better for a vinyl pool?
A vacuum head that has a brush on the bottom - no wheels.
What reaches the bottom first in a vacuum?
the brush
Why does my pool bottom feel like slime since I added the salt?
Because salt is rarely perfectly clean, Just give it a vacuum and it should be right after that. it just crap that has setled on the bottom
How do you get rid of the brown stuff at the bottom of the pool that goes right though the vacuum?
Use a suction vacuum plugged into your skimmer to vacuum to waste.
Your water is clear but some kind of scum keeps settling to the bottom even after vacuuming?
This sounds like flocculate, or clarifier, The next time you vacuum the pool gently vacuum the scum at the bottom to waste, Do not put it through the filter. you will lose a bit of water but it should top the problem from recurring if I am right.
How do you vacuum summer escape pools?
To vacuum Summer Escape pools you must work very slowly. Move the vacuum along the bottom, and do not let the vacuum head leave the bottom of the pool. Keep moving slowly along until you have vacuumed the entire pool.
How should you vacuum a deep shag rug?
With a vacuum.
Where are 4 wheel drive vacuum lines located on 1999 Kia Sportage?
you should have a chart on the bottom side of the hood. When you open the hood you should see it. That is unless the hood has been replace from an accident.
What is proper routing-connection of vacuum lines to thermostatic vacuum switch connectors?
If you have the four port vacuum switch there are two ports on the bottom and two running vertical, kind of like an upside-down "T". For the two on the bottom one comes from the vacuum advance and the other comes from the distributor delay valve. This is the valve after the "Y" in the vacuum line coming from the vacuum advance. The next one that runs vertical to the two bottom one, or the middle one, connects to EFE (or the butterfly on the exhaust manifold). The port on top goes to manifold vacuum source behind the carburator.
The air is not coming out of the front vents in your 2004 Trail Blazer LS?
The vents are opened and closed by vacuum. There should be a vacuum line running from the engine to the inside of the Trailblazer. That line is broken somewhere and it is not sending vacuum to the switch. That will cause it to blow to the top of the dash (defroster) and to the bottom (floor.) Find that line trace it back and splice a new line in where it is broken. That should fix the problem.
Should a 350 have vacuum to distributor at idle?
NO. It needs ported vacuum. This means that it should only have vacuum on it when you bring the rpms up off of adle.
