0
Scope rings are used in mounting scopes on guns and rifles. Scope rings can be purchased from several retailers as well as on several online websites.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
If I have a Savage Axis 308 and a Nikon Pro staff scope what kind of rings should I use to mount it?
Assuming that your scope is a 3x9x40 scope,then medium height rings will do the job.If it is a 3x9x50mm scope,then you will need a set of high scope rings.
What size scope rings do you need for 50mm scope on a mosberg 4x4 rifle?
50mm at least.I have found that with a 50mm objective you will need a minimum of high scope rings.Most medium hight scope rings will not give you the clearance needed for a 50mm scope objective.
How can you get a daisy scope on a crosman m4 177 pellet bb gun?
It all depends on the Daisy Scope rings that you have. The M4 has a removable front and rear sight. This will allow you to add a scope to the Weaver rail mount on the M4 if your scope rings are the weaver size. If not, then you need to purchase weaver scope rings for your scope.
A pair of Redfield scope rings can be replaced with Leupold rings?
All else being equal, yes.
What kind of scope rings do you need for a Glenfield model 25?
Just today I put weaver rings on mine. They have a 3/8 dovetail base and 1" scope rings. I had short 1" rings but I could not remove my bolt for cleaning. The rings I replaced the rings with the above mentioned. 3/8 dovetail mount 1" rings fro scope mounting see thru mounts for use of iron sights And the most important part of all is the 7/8 rise of the new mounts.
How do you install a scope on a tippman a5?
You buy 2x 3/8 weaver rail scope rings and attach them to the A5 rails. Then you put the scope you bought onto them, ensuring that they are level by looking through the scope at a level. Then you tighten the screws on the rings a little bit at a time to try to keep it level. Then your scope is mounted and ready for zeroing.
Does every paintball gun need railing for scopes?
Yes. without rails there is nothing to mount the scope (and scope rings) to.
How to install a rifle scope?
Here's the basics on mounting the scope on a rifle. ( Assuming you have a scope mount on the rifle.) 1. Place the bottom half of the scope rings on the rifle first (Without the scope attached.) 2. Place the scope on the bottom half of the rings and adjust the scope mounts to comfortably fit your eye. When adjusted, tighten down the bottom half of scope rings to the rifle mount. ( The scope should have one cross hair adjustment at the top and one on the right.) 3. Place the scope in the rings and then put the top half of the rings on. Tighten them down, but not VICE tight, just loose. You still want to move the scope some. 4. Look through the scope and align the cross hairs level with the rifle barrel. The Vertical line should be straight up and down at a right angle with the barrel. 5. when you have the scope adjusted to your eye and the barrel of the rifle, tighten the top scope rings in a crisscross pattern a little at a time. Don't vice one down then go to the next one. Do it a few turns on each one until they are tight. A final note. If you have a small screw hole and screw at the back end of the scope mount (on the rifle) you may want to place the rear scope ring against that screw. This is a scope stop. This will keep the scope from moving back from the recoil. Some scope mounts have a long pad at the rear of the scope mount that acts the same way. It's usually necessary on high powered rifles not 22's.
What scope rings do you need for Nikon 3x9x50 on a savage?
Being that the obj.is 50mm,I would put on a pair of 1in.high rings.
What current 1 inch tube scopes are compatible with the Echo scope mount with non split rings?
You've pretty much answered your own question... most any scope which can fit into one inch scope rings should be compatible. If the ends of the scope are flared out, you'd have to unscrew those, unscrew the caps on the adjustment knobs, and loosen the rings completely in order to run the scope through the rings, but the make of scope shouldn't be any problem, so long as the tube is one inch in diameter. I have found that most better quality scopes are not conducive to this. Was hoping to find one that has the windage and elevation knobs far to the rear and no flare or bell at the front of the tube so I can just slip it through both rings without having to take the scope apart.
Does a Swiss Arms 4x32 rifle scope fit well on an airsoft UTG type 96 shadow ops sniper rifle If not what scope do you recommend?
the scope is not what you want to worry about, it is the scope mounting rings find rings that will fit to your toy and the scope will mount right on , do not expect the toy to shoot dead on because it is a toy not a real weapon . don't shoot your eye out or anyone Else's eye.
Do Leapers scopes fit on the Crosman Optimus?
As long as it has an 11mm ring mount then Yes. And I think it does, or you can order 11mm scope rings for the scope.
