0
Had your aztek towed and now the AWD disabled light is on How do you turn it off?
The place to where it was towed should have fixed that. Look in your owners manual. It may have an index that explains how to turn on your all wheel drive. It is disabled when vehicles are towed. It could be a switch on your dashboard. I do not have an aztek but it is a switch on my dash. Front wheel drive gets better milage in summer. All wheel drive gets better traction in winter.
What else can I help you with?
How do you turn off oil change light aztek?
turn key on to acc,do nnot start.step on accellerator peddle three times within five seconds,turn key off,should reset
How do you turn off my vsa light in acura tl?
The light is on because you have disabled the Vehicle Stability Assist (VSA). Push the VSA button to turn the system back on and the light will go out.
How do you change the front left turn signal light bulb on a Pontiac aztek 2004?
The easiest way is to bring it to a chevy dealer, because the two were companion brands.
Are the daytime running lights on a 1998 corvette wired or connected to the turn signals as well?
No. Daytime running light can be disabled without affecting turn signals.
How can you get your 2003 Pontiac Aztek parking lights to go off and work normal again?
I wish I knew a better answer. My Aztek's lights can be turned off by turning the key to off position and then manually rotating the light button on the top left one click clockwise and then back all the way to the left. If I do this before I turn the key off, the damn thing will turn the lights back on again. Wish I had a better answer. It is clear that the Aztek designers thought God knew best when to turn its lights off and on.
How to turn off the 2009 grand caravan tire pressure light on the dash board so that it does not monitor the tire pressure?
The system can not be disabled.
How do you replace a turn signal switch for a 2003 Pontiac aztek?
To replace a turn signal switch on a 2003 Pontiac Aztek, also known as a flash relay, the steering column must be removed. The flash relay is located under the turn signal. Remove the mounting hardware and the unit can be taken off.
How do you reset the security on a 2004 aztek?
To reset the security system on a 2004 Pontiac Aztek, first, ensure you have the vehicle's key or remote. Insert the key into the ignition and turn it to the "On" position without starting the engine. Leave it in this position for about 10 minutes until the security light turns off, then turn the key to the "Off" position and back to "On" again. This process should reset the security system, allowing you to start the vehicle.
How do I reset the Security Light on Aztek?
To reset the security light on a Pontiac Aztek, first ensure that the vehicle's ignition is in the "On" position without starting the engine. Then, disconnect the battery for about 10 minutes to reset the system. After reconnecting the battery, turn the ignition back to the "On" position for a few seconds without starting the engine, then attempt to start the vehicle. If the security light remains on, you may need to consult the owner's manual for additional troubleshooting steps or consider seeking professional assistance.
How do you reset the security code on a 2002 Pontiac Aztek?
To reset the security code on a 2002 Pontiac Aztek, first, disconnect the vehicle's battery for about 10 minutes to reset the system. Reconnect the battery, then turn the ignition to the "On" position without starting the engine. Wait for about 10 minutes until the security light turns off, then turn off the ignition and restart the vehicle. If you have the original key, it may also help to use it to start the engine after the reset.
2001 Pontiac aztek tail light fuse i have no turn lights and no hazards and no brake lights the fuse box does not say what does what and i don't have the manual?
Inspect all fuses and replace blown ones May be separate circuits (multiple fuses)
How do you turn off AWD disabled light off on a Buick Rendezvous?
To turn off the AWD disabled light on a Buick Rendezvous, first ensure that the vehicle is in the correct operating mode by checking the AWD switch, which should be set to "Auto" or "On." If the light persists, it may indicate a malfunction in the AWD system, so checking for any diagnostic trouble codes with an OBD-II scanner can help identify the issue. Additionally, resetting the vehicle's computer by disconnecting the battery for a few minutes might clear the warning light, but if it remains, it's advisable to consult a mechanic.
