0
Add your answer:
Earn +20 pts
What is the formula to get neutral current in three phase transformer where three phase cureent are given?
Neutral current is the vector sum of the phase currents. You should be able to add up the phase currents from their polar quantities.
What is the current of 1MVA transformer?
This depends on the voltage, and whether it is a three phase or single phase transformer.
How three phase line current convert in single phase?
The current is the same in the three live wires. The voltage can be described as the line voltage (phase to neutral) or the phase voltage (phase to phase) which is larger by a factor of sqrt(3). So a line voltage of 230 v corresponds to a phase voltage of 400 v.
Why is important for three phase supply voltage to be in-phase?
The phase voltages (i.e. line-to-neutral in a 4-wire system, or line-to-line in a 3-wire system) of a three-phase system are displaced from each other by 120 electrical degrees. Each phase voltage, in fact, is rarely in phase with its phase current, as the phase-angle (the angle by which a phase current lags or leads its phase voltage) is determined by the load not by the supply.In general, most loads are resistive-inductive so the phase current usually lags the phase current.So, to answer your question, it's not important that a phase current is in phase with its phase voltage -if that is what you are asking.
What is the Difference between single phase current and three phase current?
given a balance three phase, three wires system with star-connected load for which lime voltage is 230v and the impedance of each phase is (6+j8)ohm. find the line current and power absorbed by each phase.
Why neutral cross section is half the phase in three phase cable while it has to carry current of summation of all phase..?
The current carried by the neutral of a three phase four wire system is the un balanced current. If the three phase system was completely balanced on all three phases there would be no need for a neutral, eg a three phase motor. This neutral current will be less that the phase current so a reduction in the neutral size is allowed.
How do you run a 220V from the box?
Three phase or two phase? Three phase requires three large wires for the current needed
How to Calculate three phase watts with unbalanced phase current?
You will need to determine the power per phase, and add them up to give the total power of the three-phase load. To do this, you will need to multiply the phase-voltage by the phase current by the power factor -for each phase.
What is the formula to get neutral current in three phase transformer where three phase cureent are given?
Neutral current is the vector sum of the phase currents. You should be able to add up the phase currents from their polar quantities.
Why the neutral cable takes high current than the phase lines in three phase installation?
In a properly balanced three phase system, there is negligible current on neutral. If there is substantial current on neutral, then the system is not balanced and/or something is wrong.
What is the limit or range of the neutral current in an unbalanced three phase system for it to be regarded as faulty?
The limit or range of the neutral current in an unbalanced three phase system is the third harmonic in single phase non-linear load current is the major contributor to neutral current.
What type of electrical current is used for three phase 408V?
Alternating current.
Why set an overload relay to full load current divide by root three in a star delta starter?
In a Wye/star system the overloads look at the phase to neutral/ground current; not phase to phase current. Which is always calculated as root three or 1.73205.............etc. Therefore the overloads have to be set to the phase to neutral/ground current.
When you have 56KVA available in 3 phase supply how much is your available current in 3 phase and how much in 1 phase?
In three phase: I = (three phase VA) / (sqrt(3) x (phase to phase voltage)) for single phase: I = (single phase VA) / ((phase to neutral voltage)) keep in mine three phase VA = 3 x (single phase VA), and phase to phase voltage = 1.732 x (phase to neutral voltage) Therefore the single phase and three phase currents are the same (ie, the three phase currents are the same in all three phases, or balanced). But don't get available current and available power confused (KVA is not the same as KW).
Is house current fit for single or three phase motor?
House current is single phase.AnswerIt depends on the system supplying your residence. Most are single phase, but some, such as here in Cyprus, have a three-phase supply as standard.
Why is the amperage in single phase double than of 3 phase?
If I have 1 KW In 3 Phase it will give 1.54 A and In single phase it will give 4.6 AFor cosF 0.9V 415 3 phV 240 1 phIt seems the reason is because the current is carried on more wires. Also, remember that if wattage stays constant, then as voltage increases, current decreases.AnswerIt really depends on the load. Are you assumining the three-phase load to be the same as the single-phase load or, as it is likely to be in practice, three times the value of the single-phase load?But, in either case, the single-phase current will not be double the the three-phase (line) current!The equation for the load current supplying a single-phase is: I = P / (E x power factor)The equation for the line current supplying a balanced three-phase system is: IL = P / (1.732 x E x power factor)If you insert real figures into these equations, (240 V for the single-phase voltage and 415 V for the three-phase line voltage) then you will find that, when the three-phase load is threetimes that of the single-phase load, the supply currents will be exactly the same. On the other hand, if you assume that the three-phase load is exactly the same as the single-phase load, then you will find that the three-phase line current will be one-third that of the single-phase current.
What is the current of 1MVA transformer?
This depends on the voltage, and whether it is a three phase or single phase transformer.
