0
since at no load only excitation current(responsible for core loss ie iron loss) flow on the primary side so core loss current will be 1A and core loss = v1*i1*powerfactor. core loss = 1*11000*0.24= 2640watt.
Wiki User
∙ 11y ago
Wiki User
∙ 14y agoa 11000/400v distribution transformer takes no load primary currnt of 1a at a power factor of 0.24 lagging Find (1) core loss current (2) iron loss
Add your answer:
Earn +20 pts
How do you minimize core losses?
Hysteresis and eddy current loss constitute core loss. It can be reduced by replacing solid core by laminated core... by adeeb
Does a transformer changes the frequency of incoming supply?
Yes the transformer effects the incoming frequency supply. This frequency is dependent on the core lamination of the transformer the weightier the core lamination the lesser will be the frequency we get and vice verse..
What is iron loss?
Iron losses (Pi) are independent of of load which occur due to pulsation of flux in the core. Iron losses include both Hysteresis loss and eddy current loss and is same at all the loads.
Is core loss same as no load loss in transformer?
Yes, that is almost true, apart from a very small copper loss in the primary winding that carries the small magnetising current. The core loss (iron loss) depends on the applied voltage. This loss is measured by the open-circuit test, carried out at the working voltage.
In transformer if frequency are reduce then what happen?
t's basically a matter of the magnetizing inductive reactance which is inversely proportional to frequency. You want to keep the magnetizing current low to minimize power loss and avoid saturating the core. The higher the frequency, the lower the required inductance for a given inductive reactance and magnetizing current, thus the smaller the required core and/or number of turns on the windings.Magnetizing current is a normal parasitic byproduct of the transformer inductance and the applied voltage level and frequency. The amount of power that can be transferred through a transformer is usually limited by the transformer winding resistances and is unrelated to the magnetizing current. Thus core size goes up at higher power levels due to larger required wire size, not due to any core limitations.
What are losses of transformer?
Core loss is one of the many fixed losses in a transformer. This means that no matter the loading of the transformer there this loss would be fixed unlike copper loss which depends on the loading of the transformer.
Why core loss depends on voltage?
Why core loss depends on voltage?
How do you minimize core losses?
Hysteresis and eddy current loss constitute core loss. It can be reduced by replacing solid core by laminated core... by adeeb
Does a transformer changes the frequency of incoming supply?
Yes the transformer effects the incoming frequency supply. This frequency is dependent on the core lamination of the transformer the weightier the core lamination the lesser will be the frequency we get and vice verse..
Is an antennas length dependent on the frequency used?
Yes.
Is no heat loss and no core loss the same thing?
No. Core losses would be hysterisis loss and eddy current losses. Heat losses most likely is referring to I2R (I squared R) losses, which is losses due to the resistance of windings, and is dependent upon loading. There are other losses that are not heat related and core related - such as losses due to vibrations (the core is a major player here, but part of the noise is from windings and cooling systems). I've never heard someone refer to losses as "no heat" or "no core". These are fundamentally impossible - there WILL be core losses, and there WILL be I2R losses if you have a transformer and it is loaded.
What are core losses?
Iron losses are termed as core losses. There are mainly two losses - Copper loss and iron loss. Iron loss is no load loss.
A sensorineural hearing loss is most often associated with loss of hearing sensitivity in which of the frequency ranges?
high frequency sounds
Why should we separate the core losses?
separation of core losses are necessary to determine core losses at diffrent frequency.........
Lowest frequency at which destructive interference is observed?
Constructive and destructive interference can occur at any frequency. Superposition of waves is not dependent on a specific frequency.
What frequency corona loss is more?
frequency is directly propotional to corona loss... so higher the freq the corona also high..
Is controlling frequency and severity of loss events can reduce risks?
Yes, controlling frequency and severity of losses reduces overall loss.
