Australia There is a material that can be bought at Bunings or for that mater most other hard wares known as aquaneadit made by selleys. It is a rod of two-part putty. You cut of the required amount to cover the problem. Kneed it until the colour is even and apply it to the damaged area. Take care that you clean the area as well as possible and rough up the plastic a little. This stuff can be applied under water to plastic cement or just about anything. If it doesn't work the wost that can happen is it will fall of.
The answer is not in the skimmer. Skimmers do not have "pressure" however, they would have suction. The suction is generated by the pump ~ the smaller part, in size, of the circulation system at the equipment pad. The pump is the small cylinder or coned shaped object that has a motor attached to it. The other object on that pad would be the larger cylinder, cannister, plastic shell or whatever is called the filter.
Back to the pump. Is the pump running? If not, why? Turn on the pump then check the skimmer. If you have water movement, all could be OK. When was the last time that you have actually opened the pump lid to empty the basket of all the debris ~ leaves, bugs, hair etc. Turn off the power to the pump and empty the basket. This task should be performed, at least, weekly.
If the pump will not start then you have a problem either with the pump or the circuit breaker or both. Reset the circuit breaker, turn on the pump. What is the pressure on the filter tank? 15# or higher. Back wash the filter if that is the type system you have. If the motor will not start then, after performing the above tasks, you may have a bad motor. After back washing the filter and the system is running ~ recheck the skimmer for flow. If you seem to have a strong flow then the problem(s) have been solved. ( Dirty filter, dirty or full skimmer or pump baskets.
Other possibilities:
Another possibility is that you may actually have something in the suction lines plugging it or restricting it. Have you vaced the pool lately? What did you vacuum up? Is the water level at the middle of the skimmer throat or high enough for water to enter into the skimmer and flow to the pump without sucking air? You may need to add water to the pool.
I have run into problems with plastic pool fittings leaking. In Australia there is a product known as selleys Aquakneedit. this stuff comes in a stick that has an outer layer that needs kneading together with the inner material of the stick. Clean the damaged area of the skimmer wit some wet and dry abrasive paper and then apply the putty to it. it has always worked well for me, up to now,
turn the pool pump off,take off the cover of the pool skimmer box, The pool water level must be above the area where the skimmer box meets the pool wall. If it is not, add water to the pool until it is at least 1 inch above this seam.
That depends on the type of skimmer in ground or above ground and from what material it is made, The water is leaking between gaskets
Dig it up and replace the leaking section.
Is the skimmer plastic? Does it have a black bottom? If so, there is a kit for this. Check out black bottom skimmer repair - search.
Best guess is that there is a leak in the return pipe from the skimmer to the pump. Sorry to say its probly not a cheap fix. There also could be a leak at the gasket around the skimmer opening.
Add thru the skimmer box
Google Aladdin pool equipment ( Lilly Pad skimmer)
You only use the skimmer/s
Adding algae control to the pool skimmer helps to disperse the chemical and coats the filter media.
Attempting to obtain step by step diagrams connecting an above ground pool to a sand filter.
The pool's manufacturer. They are not at all standardized across brands, so you need to know what brand your skimmer or pool is, and it helps if you can locate a pool store and bring the old skimmer to them - they may be able to order one, even if they don't have that brand in stock.
Yes possibly In reality, the skimmer will not cause a leak. What causes leaks are people who do not connect or glue the fittings to the skimmer properly. Or ground movement like earthquakes. k
Get a better pool skimmer normal pool skimmers usually don't do a very good job of cleaning rubbish from the surface of a pool so try a floating pool skimmer have a look on www,dragonfly.biz
The pool liner pad is placed underneath the pool liner to prevent items from cutting through the liner. If the liner is already leaking, the liner pad will not stop the leak.