0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the of a vent pipe in a plumbing systeam is to?
I don't quite get what you mean. -A vent pipe in a plumbing system is usually 1 1/2 inch ABS pipe and may extend through the roof, or may end in a AAV under a countertop.
What would happen if you connect large sewer pressure pipe to a small pressure pipe?
Nothing as long as the pressure pipe is not used for potable water as you cannot make a direct connection and depending on the GPM flow what size the larger sewer pipe is as 1 GPM (pumping) is considered 1 fixture unit when sizing the drainage system ALSO make sure the pumps system enters at a right angle 45 deg so your not eroding the side of the larger pipe out
How many kinds of steam?
There are three kinds of steam 1) saturated steam, 2)super saturated steam 3) wet steam.
Why don't the upstairs cast iron radiator heaters work?
Most often because they become air/water-locked. A cast iron radiator system works by sending steam (which naturally rises) up from the lower level into each radiator. When the steam heats the cast iron it loses enough heat so that it cools back to a water (liquid) state. When this happens, the water must flow back to the burner all by itself, propelled ONLY BY GRAVITY. So if at any point in the loop ANY length of pipe has sagged so that it is not downhill enough to allow the water to drain, the system will become locked at that point and no steam will pass by, thus cutting off heat to all radiators beyond the blockage. The most common fix for this is putting shims underneath the feet of the radiator on the opposite side of the pipe only, thus angling the radiator down for full drainage. Many times people will cause the issue themselves by putting a floor or tile underneath the radiator, inadvertently removing the angle. Other times, the natural sagging of the house removes the angle put in when the system was originally installed. So, your best bet is to 1.) Shim all non-working radiators downward toward the pipe, 2.) Drain the whole system (from the spigot at the base of the burner) of all water (and air), and 3.) re-fill the burner with water to the appropriate water pressure. Replacing the steam valves on each non-working radiator is a good idea as well.
What is steam economy in Evaporator?
Steam economy is the ratio between total steam evaporated and steam consumed Se=Steam evaporated/steam flow at start should be above 1 for multi effect systems
How can I stop steam radiator from banging?
It depends on the type of system you have. 1 pipe in, or 1 pipe in and 1 pipe out. Single pipe in/out, try replacing the relief valve or simply shimming the end of the radiator opposite where the pipe comes in. This lets water bleed out of the radiator and stops the klanging.
What are the release dates for How It Works Steam Train - 1993?
How It Works Steam Train - 1993 was released on: USA: 1 August 1993
Can glycerin be used in bending wood?
Yes. I use a turkey fryer pot 3/4 full of water and 500 ml glycerine. Bring to a boil then back off heat to maintain steam. I direct steam through a homemade steam box made of 2" PVC pipe. Steam for 2 hours per 1" thickness of wood. This method works well for kiln dried wood. You need NOT use glycerine if wood is green when bending but steam for same amount of time.
What is the temperature of steam in a closed heat pipe before it condensed and turned back into water?
That would depend on the pressure as there is something called pressure /temperature relationship @ 1 PSI the steam is 212 deg That would depend on the pressure as there is something called pressure /temperature relationship @ 1 PSI the steam is 212 deg
What do you do after you collected the pipe wrench from the girl in the steam room on SOS island?
go to youtube type in poptropica SOS island walkthrough part 1 it will tell you what to do there.
What is the of a vent pipe in a plumbing systeam is to?
I don't quite get what you mean. -A vent pipe in a plumbing system is usually 1 1/2 inch ABS pipe and may extend through the roof, or may end in a AAV under a countertop.
Can you join 1 inch copper pipe to 28mm copper pipe?
I have recently had to join a 1 inch steel water pipe to a new copper 28mm pipe. You can do this using a 28mm comression joint. 1inch is just uneder 28mm in diameter but the compression joint takes up the difference and works without fault or leaks.
What is the KKS Kraftwerk-Kennzeichen System code for Brine Line?
Actually their is no definite KKS Code for Geothermal Steam Field, especially for Geothermal Steam Pipe line identification.... You can used LBA for Geothermal Steam Field coding with variation on its "Numerical Sequencing" (under BDL 1&2) and LBB & LBJ for Geothermal Power Plant, also used variation on its "Numerical Sequencing" for proper line identification.from "Albert Einstein" of the Philippinesdsdelarosajr@yahoo.com
Which measuring system describe steam ATA as units?
1 ata= how many bars, 1 ata=how many kg/cm2
What would happen if you connect large sewer pressure pipe to a small pressure pipe?
Nothing as long as the pressure pipe is not used for potable water as you cannot make a direct connection and depending on the GPM flow what size the larger sewer pipe is as 1 GPM (pumping) is considered 1 fixture unit when sizing the drainage system ALSO make sure the pumps system enters at a right angle 45 deg so your not eroding the side of the larger pipe out
What is the inlet pressure of a condensate tank?
It can be at any pressure less than the main steam pressure. I've operated steam systems with condensate tanks at widely varying pressures. The pressure a condensate tank, (which condenses some steam, but typically takes returns from steam traps) is wholly dependent on the system is installed in. Some heating system condensate tanks are designed to handle no more than 30 psig (minimum design requirement) yet take condensate at 1 or 2 psi from the steam traps. Other high pressure production lines operating at 50 - 100 psig could discharge to a tank at 50 - 100 psi, though the actual pressure would be reduced by the length of pipe transferring it to the tank. And the highest pressure I've operated a condensate system at was 600 psig, the steam system drew the steam for process from an extraction stage on the turbine at nominally 600 psi, though at low loads it was typically a much lower pressure.
How do I add freon to a 1996 Audi A4 Quattro?
Buy a kit from auto parts or Wal-Mart comes with instructions Actually, this A4 only has a high pressure port. The Walmart / Autozone kits should really only be used with a low pressure port. I would find a someone that works on VWs. What I did was to get a low presure pipe with the valve in the junker, cut the valve leaving 1-1/2" of pipe in both sides of the valve, then I open the pipe in half, make a hole in the low pressure pipe and clamp the low valve with hose clamps, I use a rubber hose as a seal. recharge system and done. Works perfect.
