Computer Architectures - Digital Circuits - Latches and flip-flops
In the same way that gates are the building blocks of combinatorial circuits, latches and flip-flops are the building blocks of sequential circuits.
While gates had to be built directly from transistors, latches can be built from gates, and flip-flops can be built from latches. This fact will make it somewhat easier to understand latches and flip-flops.
Both latches and flip-flops are circuit elements whose output depends not only on the current inputs, but also on previous inputs and outputs. The difference between a latch and a flip-flop is that a latch does not have a clock signal, whereas a flip-flop always does.
Latches
How can we make a circuit out of gates that is not combinatorial? The answer is feed-back, which means that we create loops in the circuit diagrams so that output values depend, indirectly, on themselves. If such feed-back is positive then the circuit tends to have stable states, and if it is negative the circuit will tend to oscillate.
A latch has positive feedback. Here is an example of a simple latch:
A transparent latch (or simply a latch) is a digital logic device that can store two stable states with a level sensitive control signal called enable/latch, when this control signal is in the enable state the latch device transparently passes its input signal to its output, when this control signal is in the latch state the latch device holds its output in the current state and ignores the input signal. This behavior is different from flip flops (e.g. D flip flop), which are usually clocked and often edge sensitive not level sensitive.
Applications electronic latch are the functions as a circuit and helps when creating memory devises. These are use everyday in are day to day experiences
because it doesnt
Latch A latch remembers the last state it was told to with another latchingsignal Buffer A buffer merely strengthens a signal so that it canbe fanned out with integrity or drive a heftier device. Any amplifieris a buffer. It outputs a state only as long as the state persistson its input(s).
A D latch is level triggered. It will follow the input as long as the gate is true. Once the gate goes false, the output will stay at the last known value. A D flip flop is edge triggered. The output will not change until the edge of the gate. At that point, the output will go to the state of input, and then it will stay at that value.
I believe the 2003 - and newer have the LATCH System. Check related link below... How the LATCH System Works on Car Seats
I opened my hood with the latch and when I went ot close it the latch no longer works. Is ther some way I can close and secure my hood shut?
How do i get the trunk to close when it sometime works
Pull the inner panel and actuate the latch manually.
my latch is broken on my Honda and all i did was put a bungy cord thru the loop in the hood and pull it to the tow hitch on the bottom of the car and it works fine
Does it work from the outside with the key? That way it will make easier to get to the latch to see if you can get it work. I had the opposite problem in my 94, the hatch was open and the latch wouldn't close. I took the inner panel off (just Phillips screws) and the plate underneath that covers the latch. I used a lot of WD40 and worked the latch back and forth by hand and got it freed up so it works properly. That was 9+ months ago and it still works just like it should. Not sure if this will work for a latch that is stuck closed. I'm assuming that you have already checked your fuses to make sure there is power going to the latch. Hope this is some help with your problem. Good luck.
The best way is to find a similar vehicle, open the hood on the car that the hood release works on. Then try to figure how the latch mechanism works. The you can fashion a tool to trip the latch. Also, lie down and use a flashlight - look up and see if you can unbolt the latch bar. This works very well on Chevy blazers. You will need a long extension. If you let us know what type of car you have perhaps we can be of more help.
YOu will have to remove the inner door panel to get to the works
Hmm,i have same problem where hood latch does not catch.You can get the darn thing out spray it with some wd-40 it works for awhile till you got to do it again.
static latch: a latch without capacitor dynamic latch: latch with capacitor
Yes it works great! Have taken two kids through all those years
I used a short bunge cord hooked on the metal bracket in back of the box to the front latch. Not the best fix - but it works (bertter than paying $90 for a new box).