0
How and why do fingerprints develop on the surface of objects and what is the most common form of latent fingerprint development A Glass Glossy Magazine Cover Painted Wood and Phone Receiver?
Wiki User
∙ 10y ago
Impressions of fingerprints may be left behind on a surface by the natural secretions of sweat that is present in friction ridge skin, or they may be made by ink or other substances transferred from the peaks of friction ridges on the skin to a relatively smooth surface.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
How do you put the word receiver general in a sentence?
The Receiver General for Canada is currently unavalable for comment.
Heat energy can be transferred from a source to a receiver by?
Heat energy can be transferred from a source to a receiver by conduction, convection, and radiation.
Can you watch SVT2 lively in the internet?
Freely: No Just if you purchase an receiver and a smart card directly from the channel. Squirrl
Does Police radar work at night?
Yes!!! Radar uses its own emitter. To the receiver it is always night until the transmitter is tuned on. Turning on the transmitter is like turning on a flashlight.
What is the purpose of a word descrambler?
The official oxford definition of the word descrambler is that in telecommunications a scrambler is a device which mixes signals up so that a receiver cannot read them as they were transmitted. A descrambler therefore does the opposite.
How do you remove the magazine tube on a 870 Remington shotgun?
The actual magazine tube that connects to the receiver is brazed in there, so it removing it isn't an optimum solution.
Is Mexico a donor nation?
No. Mexico is a receiver of development aid.
Where can the serial of a browning auto 5 be found on the gun?
On the bottom of the receiver just forward of the magazine port. American A5s are on the left hand side of the receiver
Is a automatic pistol without a clip be considered a gun floridagun in Fla?
A firearm is a firearms, regardless of whether or not is has the magazine with it. The receiver is the part which is considered the basis of the firearm, not the magazine.
How do you load a semi aut shot gun?
That depends on the model and the feed system. For example, a Saiga uses a detachable magazine, so you'd load the magazine, attach the magazine, cycle the action, and you'd be ready to go. Some shotguns with tubular magazines load from a port in the bottom of the receiver, and some have a cutout in the side of the receiver which you would push the shotgun shells into.
How do you remove magazine tube on Stevens 87d?
To remove the magazine tube on the Stevens 87D, first ensure the firearm is unloaded. Then, unscrew the end cap at the front of the magazine tube. Slide off the end cap and follower, then push the magazine spring and follower out through the rear of the tube. Finally, slide the magazine tube out of the receiver.
Where is the serial stamped on a model 37 Ithaca?
On my 1950s vintage Ithaca Model 37 16 gauge it is on the right side of the end of the receiver where the magazine tube and barrel go into the receiver, and also on the barrel adjacent to the number on the receiver. The numbers should be the same on both the barrel and receiver unless the barrel is not the original barrel, at least on mine they are.
What does the lever on the left side of the receiver of a browning a-5 do?
It blocks off the magazine to allow the shooter to change the shell in the chamber without needing to empty the magazine or manipulate the lifter. The "classic" use was changing from a duck load to a goose load.
How do you take the plug out of a Remington 870?
You'll start by unscrewing the magazine cap fron the end of the magazine. It's the knurled knob that also holds the barrel in the receiver. The forearm slides back and forth on the magazine. Gently pry out the spring stop once the cap is off. The spring and plug/follower should just fall out when the weapon is held down, but if you're not holding the barrel, it'll fall out of the receiver also. Some magazine plugs have molded weak points that allow you to break them off to increase the amount of ammo in the magazine. A large pair of pliers with padded jaws may be needed to break the cap loose. Brownells carries weapon specific tools for gunsmiths and they sell to civilians. You'll start by unscrewing the magazine cap from the end of the magazine. It's the knurled knob that also holds the barrel in the receiver. The forearm slides back and forth on the magazine. Gently pry out the spring stop once the cap is off. The spring and plug/follower should just fall out when the weapon is held down, but if you're not holding the barrel, it'll fall out of the receiver also. Some magazine plugs have molded weak points that allow you to break them off to increase the amount of ammo in the magazine. A large pair of pliers with padded jaws may be needed to break the cap loose. Brownells carries weapon specific tools for gunsmiths and they sell to civilians.
How do you load a repeating rifle?
There are several types of repeating rifles, fed by different systems. Some rifle have detachable magazines, while others may have fixed magazines. Of fixed magazine rifles, you may have either a box magazine. or a tubular magazine. In any of these instances, you would load the magazine. If the rifle was fed by a detachable magazine, you would then insert the magazine into the magazine well and ensure that it was seated. Rifles with fixed box magazines, such as bolt action rifles or the SKS, will require you to open and lock the action to the rear, then feed the rounds into the magazine through the open action. Rifles with tubular magazines may have different ways of loading the magazine. Some will have a slot on the side of the receiver which cartridges are fed into to load the magazine. Some will require the end of the tubular magazine to be removed, and for the cartridges to be fed in from the front of the magazine (below the bore), after which, the cap (which often contains the magazine spring) is replaced. Some tubular magazines are fed through an opening in the bottom of the receiver (this is most common with shotguns). Some tubular magazines are inserted through the buttstock, such as on certain versions of the Remington Nylon 66. On these rifles, you would remove the tubular magazine completely from the rifle, load the cartridges into the magazine, then insert it back into the opening in the buttstock and secure the magazine.
What are the major parts of a pistol?
Depends on the pistol- there are multiple designs. In the case of a semi-automatic, it will generally consists of the receiver (frame) barrel, lockwork, magazine and grips.
How can you get the bolt out from a 30-40 Krag rifle?
Point the muzzle in a safe direction, pull back the bolt and open the magazine. Visually verify that the weapon is unloaded. Lift the extractor and rotate the bolt to the left until the extractor clears the receiver. Pull the bolt back and out of the receiver.
